USER'S INSTRUCTIONS: The project work you are about to view is on "design and fabrication gas burner" Please, sit back and study the below research material carefully. This project topic "design and fabrication gas burner" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and fabrication gas burner" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and fabrication gas burner" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

DESIGN AND FABRICATION GAS BURNER

BY

---
EE/H2013/01430
DEPARTMENT OF ---
SCHOOL OF ---
INSTITUTE OF ---

DECEMBER,2018

---

APPROVAL PAGE

This is to certify that the research work, "design and fabrication gas burner" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a B.Sc on --- has been approved.

By
Dr. ---                                                    Dr. ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
 Dr. ---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work “design and fabrication gas burner” research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of “the rate and causes of infant mortality in edo state (case study of irrua specialist teaching hospital)” visible for everyone, then the complete material on “the rate and causes of infant mortality in edo state (case study of irrua specialist teaching hospital)” is to be ordered for. Happy viewing!!!

---

Burners play an integral role in oil and gas well pads. They generate the heat necessary for separating the oil, gas and water mixture and to keep the gases in their vapor phase during transportation through pipelines. Burners typically use a portion of the gas coming out of the ground as the fuel to produce the flame for heating. The gases extracted from the ground enter the burner skid (commonly referred to as burner fuel train) at a high pressure and hence they need to be pressure controlled for use in burners. This work is on fabrication of a gas burner.

 

TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT

CHAPTER ONE
INTRODUCTION
1.1      BACKGROUND OF THE PROJECT

• OBJECTIVE OF THE PROJECT
• HOW COMBUSTION OCCUR IN BURNER
• SIGNIFICANCE OF THE PROJECT
• APPLICATION OF THE PROJECT
• LIMITATION OF THE PROJECT

CHAPTER TWO
LITERATURE REVIEW

• REVIEW OF FUEL GAS
• HISTORICAL BACKGROUND OF FUEL
• FLAME TEMPERATURES OF COMMON GASES AND FUELS
• EXPLOSIVE LIMITS AND IGNITION TEMPERATURES OF COMMON GASES
• COMBUSTION VALUES OF COMMON GASES

CHAPTER THREE
METHODOLOGY

• MAJOR COMPONENTS OF INDUSTRIAL GAS BURNER
• PICTORIAL DIAGRAM GAS BURNER
• WORKING PRINCIPLE OF THE PROJECT

CHAPTER FOUR

• ASSEMBLY AND TESTING
• BURNER CONFIGURATION
• TESTING THE CONFIGURATION
• SELECTION OF BURNER

CHAPTER FIVE

• CONCLUSION
• RECOMMENDATION
• REFERENCES

CHAPTER ONE
1.0                                                        INTRODUCTION
A burner is a mechanical device that supplies required amount of fuel and air creates condition for rapid mixing of fuel and air produces a flame which transfers thermal energy to furnace and charge.
In oil burners, oil is atomized into a fine spray by a spray nozzle and air is supplied for combustion in the spray chamber. Alternatively oil may be atomized by high speed air to produce a fine dispersion of droplets into air.
There are liquid fuel and gaseous fuel burners. In liquid fuel burner, oil is heated and atomized either mechanically or by high speed gaseous jet.
This work focuses on a gas burner is a device which is used to generate a flame, in order to heat up products using a gaseous fuel such as acetylene, natural gas, or propane. Some burners have an air inlet to mix the fuel gas with air, to enable complete combustion. Acetylene is commonly used in combination with oxygen.
The gas burner has many applications such as soldering, brazing and welding, the latter using oxygen instead of air for producing a hotter flame, which is required for melting steel. For laboratory uses, a natural-gas fueled Bunsen burner is used. For melting metals with melting points of up to 1100 °C (such as copper, silver, and gold), a propane burner with a natural drag of air can be used.

1.1                                             OBJECTIVE OF THE PROJECT
The objective of this work is to design a device which is used to generate a flame, in order to heat up products using a gaseous fuel such as acetylene, natural gas, or propane.

1.2                                 HOW COMBUSTION OCCUR IN BURNER
The release of potential energy of fuel by combustion with air requires several
stages, namely.
• Mixing of air and fuel
• Ignition of the mixture
• Chemical reaction
• Disposal of products of combustion from the reaction site so that fresh reactants are available. Except mixing of air and fuel, all other stages are extremely fast such that it is said that if fuel and air are mixed, fuel is burnt. Accordingly mixing is the slowest step in the process of combustion This can be understood by considering that each mole of carbon theoretically requires 1 mole of oxygen for complete combustion. But 1 mole of oxygen is obtained from 4.76 moles of air. That means 3.76 moles of nitrogen are present with 1 Mole of oxygen. Nitrogen is inert and does not take part in combustion therefore mixing of air+ fuel is important.

1.3                                         SIGNIFICANCE OF THE PROJECT
A gas burner is a device which is used to generate a flame, in order to heat up products using a gaseous fuel such as acetylene, natural gas, or propane. Some burners have an air inlet to mix the fuel gas with air, to enable complete combustion. Acetylene is commonly used in combination with oxygen.

1.4                                          APPLICATION OF THE PROJECT
The hottest and most efficient of all fuel gases use in gas burner, acetylene (C2H2) provides high levels of productivity thanks to good localized heating with a minimum of thermal waste. It also requires the least amount of oxygen to ensure complete combustion. This flammable, colourless gas is lighter than air so does not accumulate at low levels, where it could cause a potential hazard. It is generally supplied dissolved in acetone or DMF (dimethylformamide) in specially designed cylinders to prevent decomposition.
A low flame moisture content makes this fuel gas a good choice for many critical heating processes. Typical applications include flame heating, flame gouging, welding, flame hardening, flame cleaning, flame straightening, thermal spraying, spot-heating, brazing, texturing, profile-cutting, branding wooden pallets, wood-ageing and carbon coating.
Acetylene is the only fuel gas recommended for underground working conditions because it is lighter than air. It is also the only fuel gas, for instance, which can be used to weld steel.
In cutting, oxy-acetylene gives the fastest preheating and piercing times of any fuel gas combination.

Benefits include:

• Improved cut quality
• Higher cutting speeds
• Faster cut initiation time
• Reduced oxygen use.

1.5                                           LIMITATION OF THE PROJECT

• this device can be hazardous when not properly handled

 

CHAPTER TWO: The complete chapter two of “design and fabrication gas burner” is available. Order full work to download. Chapter two of “design and fabrication gas burner” consists of the literature review. In this chapter all the related work on “design and fabrication gas burner"

CHAPTER THREE: The complete chapter three of “design and fabrication gas burner” is available. Order full work to download. Chapter three of “design and fabrication gas burner” consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of design and fabrication gas burner” is available. Order full work to download. Chapter four of “design and fabrication gas burner” consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of design and construction of a “design and fabrication gas burner” is available. Order full work to download. Chapter five of “design and fabrication gas burner” consist of conclusion, recommendation and references.

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

You can also visit our facebook Page at fb.me/hyclas to view our related construction (or design) picture.

---

For more information contact us through Any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com

---

IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.