USER'S INSTRUCTIONS: The project work you are about to view is on "comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor". Please, sit back and study the below research material carefully. This project topic ( comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor) have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
COMPARATIVE ANALYSIS ON THE EFFECT OF DIFFERENT METHODS OF STARTING THREE PHASE SQUIRREL CAGE INDUCTION MOTOR
BY
---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work, " comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.
By
--- . ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work "
comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "
comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" visible for everyone, then the complete material on "
comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" is to be ordered for. Happy viewing!!!
Induction Motor is the most widely used motor due to this reliability robust and low cost and it is used in both household. An industrial application is due to their high torque to volume ratio, ruggedness and low maintenance. Induction Motor draws a high starting current during starting period which effects on electromagnetic torque, speed and current. Traditional method include DOL, auto transformer, star delta starter etc. control this parameter up to certain limits. This study is about the starting method of induction motor DOL starter, star delta, autotransformer starter. Analysis is made for speed, torque and current during start. Simulation is made in MATLAB and comparatively results are estimated.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE STUDY
- PROBLEM STATEMENT
- AIM AND OBJECTIVES OF THE STUDY
- SIGNIFICANCE OF THE STUDY
- SCOPE OF THE STUDY
- LIMITATION OF THE STUDY
- RESEARCH METHODOLOGY
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- INTRODUCTION
- OVERVIEW OF STARTER
- REVIEW OF RELATED LITERATURE
- COMPARATIVE ANALYSES REVIEW
- HISTORICAL BACKGROUND OF AN AC INDUCTION MOTOR
CHAPTER THREE
3.0 METHODOLOGY
- ANALYSIS OF DIFFERENT STARTING METHOD
- DIRECT-ON-LINE STARTING OF INDUCTION MOTOR
- STAR-DELTA STARING OF INDUCION MOTOR
- AUTO-TRANSFORMER STARTING OF INDUCTION MOTOR
3.2 COMPARISON OF OUTPUT WAVEFORM OF STARTING PARAMETERS
CHAPTER FOUR
4.0 RESULTS AND DISCUSSION
- RESIULT
- DISCUSSION
CHAPTER FIVE
- CONCLUSION
- REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE STUDY
Starting induction motors on isolated or weak systems is a highly dynamic process that can cause motor and load damage as well as electrical network fluctuations. Mechanical damage is associated with the high starting current drawn by a ramping induction motor. In order to compensate the load increase, the voltage of the electrical system decreases. Different starting methods can be applied to the electrical system to reduce these and other starting method issues.
A 3-phase induction motor is theoretically self-starting. The stator of an induction motor consists of 3-phase windings, which when connected to a 3-phase supply creates a rotating magnetic field. This will link and cut the rotor conductors which in turn will induce a current in the rotor conductors and create a rotor magnetic field. The magnetic field created by the rotor will interact with the rotating magnetic field in the stator and produce rotation. Based on the construction of the rotor, a 3-phase induction motor can be categorized into two types:
- Squirrel Cage Induction Motor
- Wound Rotor or Slip Ring Induction Motor
The stator of both types of motors consists of a three phase balanced distributed winding with each phase mechanically separated in space by 120 degrees from the other two phase windings. This gives rise to a rotating magnetic field when current flows through the stator.
In squirrel cage IM, the rotor consists of longitudinal conductor bars which are shorted at ends by circular conducting rings. Whereas, the wound rotor IM has a 3-phase balanced distributed winding even on the rotor side with as many number of poles as in the stator winding.
Squirrel cage induction motor just before starting is similar to a poly phase transformer with a short-circuited secondary. If normal voltage is applied to the stationary motor then, as in the case of a transformer, a initial current, to the turn of 5 to 6 times the normal current or the normal rated current, will be drawn by the motor from the mains. This initial excessive current is objectionable, because it will produce line voltage (The potential difference or the voltage across two phases) drop, which in turn will affect the operation of the other electrical equipment and the lights connected to the same line.
The initial rush of current is controlled by applying a reduced voltage to the stator (motor) winding during the starting period and then the full normal voltage is applied when the motor has run up to speed. For the small capacity motors say up to 3H.P, full normal voltage can be applied at the start. However to start and stop the motor and to protect the winding from the over load current and low voltages, a starter is required in the motor circuit. In addition to this the starter may also reduce the applied voltage to the motor at the time of starting. A 3-phase induction motors employ a starting method not to provide a starting torque at the rotor, but because of the following reasons:
- Reduce heavy starting currents and prevent motor from overheating.
- Provide overload and no-voltage protection starter.
1.2 PROBLEM STATEMENT
Induction motor starting is a highly dynamic process that can have many adverse effects on the entire power system. Two of the prominent issues are the effects caused by high inrush currents on the mechanical system of the load, and the response of the generation source to the load step, of which voltage dip is of most concern. To address these issues, different starting methodologies have been developed to mitigate damaging effects. It is not economically practical to test each of these methods on a physical system because of possible equipment damage, electrical system vulnerability, and other problems. Through simulation of these systems it possible to compare the various starting methods in an economical, secure and yet effective manner.
1.3 AIM AND OBJECTIVES OF THE STUDY
The main aim of this study is to compare different types of motor starter according to their simulation models. The objectives of this work are as follows:
- To study the starting period of induction motor when it’s connected with different starter at the time of starting.
- To analysis starting current, torque and speed of induction motor when it is started with the help of direct-on-line, star-delta and auto-transformer starter.
- Using MATLAB SIMULINK we are going to compare their output form.
1.4 SIGNIFICANCE OF THE STUDY
This study will help to understand the starting period and their effect on induction motor. By building an accurate and usable simulation models this work is can aid the designer in making the choice of an appropriate motor starting method.
1.5 SCOPE OF THE STUDY
The purpose of this work is to develop an accurate simulation for comparing starting methods of a squirrel cage induction motor system. This work is to provide a comprehensive approach to simulate the starting methods and dynamic machine models for this type of system. The simulation program is performed in Matlab/Simulink as it has become a widely used and accepted platform. Matlab/Simulink allows for easily testing different simulation step times and solution algorithms (TransÉnergie Technologies Inc., 2003).
1.6 LIMITATION OF THE STUDY
As we all know that no human effort to achieve a set of goals goes without difficulties, certain constraints were encountered in the course of carrying out this project and they are as follows:-
- Difficulty in information collection: I found it too difficult in laying hands of useful information regarding this work and this course me to visit different libraries and internet for solution.
- Difficulty in parts gathering: I found it too difficult when setting up the simulation equipment because of the unfamiliarity of the equipment used.
1.7 RESEARCH METHODOLOGY
In the course of carrying this study, numerous sources were used which most of them are by visiting libraries, consulting journal and news papers and online research which Google was the major source that was used.
1.8 PROJECT ORGANISATION
The work is organized as follows: chapter one discuses the introductory part of the work, chapter two presents the literature review of the study, chapter three describes the methods applied, chapter four discusses the results of the work, chapter five summarizes the research outcomes and the recommendations.
CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of " comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" is also available. Order full work to download. Chapter two of " comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" consists of the literature review. In this chapter all the related work on " comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" was reviewed.
CHAPTER THREE: The complete chapter three of "comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" is available. Order full work to download. Chapter three of " comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of "comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" is available. Order full work to download. Chapter four of " comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of "comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" is available. Order full work to download. Chapter five of " comparative analysis on the effect of different methods of starting three phase squirrel cage induction motor" consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
For more information contact us through any of the following means:
Mobile No 
:+2348146561114 or +2347015391124 [Mr. Innocent]
Email address 
:engr4project@gmail.com
Watsapp No 
:+2348146561114
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
FOLLOW / VISIT US VIA:
