DESIGN AND CONSTRUCTION OF A BATTERY CHARGER WITH OVER-CHARGE CUT-OFF
USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a battery charger with over-charge cut-off". Please, sit back and study the below research material carefully. This project topic "design and construction of a battery charger with over-charge cut-off" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a battery charger with over-charge cut-off" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a battery charger with over-charge cut-off" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
BY
---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---
APPROVAL PAGE
This is to certify that the research work, "design and construction of a battery charger with over-charge cut-off" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.
By
--- . ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work "design and construction of a battery charger with over-charge cut-off" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and construction of a battery charger with over-charge cut-off" visible for everyone, then the complete material on "design and construction of a battery charger with over-charge cut-off" is to be ordered for. Happy viewing!!!
A battery charger is an electrical device employed for charging batteries. These batteries that are usually charged by battery charger are the storage batteries also known as “accumulator” the battery charger changes. The alternating current forms the power line into d.c suitable for charging.
When the battery is fully changed, is up to it’s maximum, 12 volt, the charger with automatically cut-off with the help of the contact relay, the transistor and the zener diode when bend the current back to the system, and the system have the ability to indicate when the battery is charging or not, when the battery is empty or fully charged.
Cover page
ii. Certification
iii. Dedication
iv. Acknowledgement
v. Abstract:
CHAPTER ONE
INTRODUCTION
- Background of the Study
- Problem Statement
- Hypothesis/Research Questions
- Objective of Study
- Significance of Study
- Scope of Study
- Limitations of Study
- Definitions of terms
CHAPTER TWO
LITERATURE REVIEW
2.1 Review of Related works
2.2 Contribution to Knowledge
2.3 Proposed system’s Theories
2.4 Expected Results from Hardware &Software
CHAPTER THREE
DESIGN METHODOLOGY
3.1 The Block Diagram of a Battery Charger
3.2 System Circuit
3.3 System Operation
3.4 Circuit Description
CHAPTER FOUR
RESULTS/ANALYSIS
4.1 CONSTRUCTION PROCEDURE AND TESTING ANALYSIS
4.2 Casing And Packaging
4.3 Assembling Of Sections
4.4 Tests an Operation
4.5 Battery Charger Casing
CHAPTER FIVE
SUMMARY,CONCLUSION AND RECONMENDATIONS
5.1 Summary
5.2 Conclusion
5.3 Recommendation
References
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE STUDY
A battery charger is described as is a device that provides electricity to convert into stored chemical energy for storage in an electrochemical cell by running an electric current through it. [Zhang et al, 2013].
A battery charger consists of a rectifier circuit, power circuit, ripple monitoring, control circuit, regulator circuit.
A Battery charger comes in various designs and voltage. The choice of a particular charger depends largely on the size of battery. Mini battery charger could be used to charge batteries whose voltage is 12 volts.
The battery charge is built in such a way that it delivers a constant value of d.c current into the battery it is charging in the opposite direction from which current flows on the batteries during discharge one cannot successfully design a battery charge without a fundamental understanding of the accumulator because it also makes up the operation according to [Zhang et al, 2013].
This work is aimed at building an automatic battery charger which comprises of overcharge cut – off feature.
- Problem Statement
There is nothing that is as frustrating and dangerous as when a battery is plugged and at the end it was discovered that the battery did not charge. And nothing is as dangerous as when a battery was fully charged and the owner is not aware of the charging state. This study solve problems such as not knowing when a battery is charging and when it is fully charged which can cause the battery not to charged or to over-charge.
The battery charge is built in such a way that it delivers a constant value of d.c current into the battery it is charging in the opposite direction from which current flows on the batteries during discharge one cannot successfully design a battery charge without a fundamental understanding of the accumulator because it also makes up the operation.
- Aim and Objective of Study
The main aim of this work is to build an automatic battery charger which comprises of indicators that indicates charging process and charging level indicator. The objectives are:
- To build the device
- To know when a battery is charging or not
- To know the status of a battery thereby saving the battery from over-charge
- Significance of Study
Carrying this work will go along way teaching students how battery charger is been made and the operation of battery charger. This study will also be of great benefit to all users of charger and rechargeable devices in that it will help them to understand how their battery is been charged and how chargers are operated.
- Scope of Study
The scope of this work focuses on the building of a 12v battery that incorporated overcharge cut-off relay. In this work, a voltage sensor circuit is incorporated to sense the voltage of the battery under charge. The charger has the ability to automatically switch OFF when the battery voltage reaches the required optimum level with the help of the contact relay, the transistor and the zener diode.
- Limitations of Study
This charger can only be used for 12v batteries. The final packaging of the device will compose of two LEDs which includes LED for power, and overcharge cut-off LED.
- Definitions of terms
Below are terms that are frequently used in this work and their definitions:
Battery: a container consisting of one or more cells, in which chemical energy is converted into electricity and used as a source of power.
Charger: a device for charging a battery or battery-powered equipment.
Capacitor - a charge storage device made up of two metallic plates separated by a dielectric, with equal but opposite charges. The AC impedance of a Capacitor is (1 / jWL) and acts as an open circuit in DC applications.
Circuit - a complete path that allows electrical current from one terminal of a voltage source to the other terminal.
Alternating (AC) Current - currents that have a harmonic time dependence.
Ampere (A) - the unit of measurement for electrical current in coulombs per second.
CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and construction of a battery charger with over-charge cut-off" is also available. Order full work to download. Chapter two of "design and construction of a battery charger with over-charge cut-off" consists of the literature review. In this chapter all the related work on "design and construction of a battery charger with over-charge cut-off" was reviewed.
CHAPTER THREE: The complete chapter three of "design and construction of a battery charger with over-charge cut-off" is available. Order full work to download. Chapter three of "design and construction of a battery charger with over-charge cut-off" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of "design and construction of a battery charger with over-charge cut-off" is available. Order full work to download. Chapter four of "design and construction of a battery charger with over-charge cut-off" consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of "design and construction of a battery charger with over-charge cut-off" is available. Order full work to download. Chapter five of "design and construction of a battery charger with over-charge cut-off" consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
For more information contact us through any of the following means:
Mobile No 
:+2348146561114 or +2347015391124 [Mr. Innocent]
Email address 
:engr4project@gmail.com
Watsapp No 
:+2348146561114
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
FOLLOW / VISIT US VIA:
