phonelogo+234 8146561114 or +2347015391124
DESIGN AND CONSTRUCTION OF A DARK ACTIVATED SWITCH USING LIGHT DEPENDENT RESISTOR

USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a dark activated switch using light dependent resistor". Please, sit back and study the below research material carefully. This project topic (design and construction of a dark activated switch using light dependent resistor) have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a dark activated switch using light dependent resistor" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a dark activated switch using light dependent resistor" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.


APPROVAL PAGE

This is to certify that the research work, "design and construction of a dark activated switch using light dependent resistor" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator


DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.


PROJECT DESCRIPTION: This work "design and construction of a dark activated switch using light dependent resistor" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and construction of a dark activated switch using light dependent resistor" visible for everyone, then the complete material on "design and construction of a dark activated switch using light dependent resistor" is to be ordered for. Happy viewing!!!


ABSTRACT

This work is aimed at activating a switch or AC lamp at sunset and deactivate it at sunrise.
This Dark activated Switch can trigger a relay to operate an AC lamp at Sunset. The lamp remains on till morning and then turns off. This eliminates the need of switching the Porch lamp or Backyard lamp daily and also helps to light the premises of the house when the occupants are out of station.
The circuit utilizes the light sensing property of LDR to activate the circuit. The LDR (Light Dependent Resistor) has very high resistance as high as 10 Meg ohms in dark which reduces to a few Ohms in bright light.

TABLE OF CONTENTS

 TITLE PAGE

APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRCT
TABLE OF CONTENT

CHAPTER ONE

    • INTRODUCTION
    • BACKGROUND OF THE PROJECT
    • PROBLEM STATEMENT
    • AIM/OBJECTIVE OF THE PROJECT
    • SCOPE OF THE PROJECT
    • SIGNIFICANCE OF THE PROJECT
    • LIMITATION OF THE PROJECT
    • APPLICATION OF THE PROJECT
    • METHODOLOGY
    • PROJECT ORGANISATION

CHAPTER TWO

LITERATURE REVIEW
2.0      LITERATURE REVIEW
2.1      REVIEW OF LIGHT SENSOR
2.2      LDR STRUCTURE AND WORKING
2.3      REVIEW OF THE MAJOR COMPONENTS USED

CHAPTER THREE

3.0      CONSTRUCTION METHODOLOGY
3.1      BLOCK DIAGRAM OF THE SYSTEM
3.2      CIRCUIT DIAGRAM
3.3      CIRCUIT DESCRIPTION
3.4      SYSTEM OPERATION
3.5      COMPONENTS LIST
3.6     DESCRIPTION OF MAJOR COMPONENTS USED

CHAPTER FOUR

4.0       RESULT ANALYSIS

4.1      CONSTRUCTION PROCEDURE AND TESTING
4.2      ASSEMBLING OF SECTIONS
4.3      CONSRUCTION OF THE CASING
4.4      TESTING OF SYSTEM OPERATION
4.5    INSTALLATION OF THE COMPLETED DESIGN
4.6    COST ANALYSIS

CHAPTER FIVE

    • CONCLUSIONS
    • RECOMMENDATION

5.3     REFERENCES

CHAPTER ONE
1.0                                                        INTRODUCTION
1.1                                         BACKGROUND OF THE PROJECT
The controlling of lights such as security light is usually done by the occupant of the house. This is not only precarious but also sometimes results in wastage of power because of the negligence or unusual circumstances on part of the technician in operating the lights on and off. Not only in case of security lights, even for controlling the home appliances like garden or outdoor lights, we can utilize the dark activated switch for automatic switching of the lights based on daylight’s intensity by using a light sensor.
Dark Activated Switch is a  electrical project circuit by which we can switch on and off the electrical load appliances like lights, fans, coolers, air conditioners, street lights, etc., automatically based on the day-light intensity instead of manually operating the switches.
By using this method, manpower can be reduced to a great extent. In case of the street lights/lamp erected on highways it is not an easy task to manually control them, but, if uncontrolled, the chances of power wastage would increase. To get rid of this situation, the implementation of automatic light switch by using a dark sensor that switches lights automatically on and off is the best option.

1.2                                                  PROBLEM STATEMENT
In the last decade, home light or security light is been controlled by human being or occupant of house and this involves labour, waste time and sometime may not be switched in time or may also be forgotten which will result waste of energy. This eliminates this problem, this device was built which is used to daily and also helps to switch ON and OFF of house light daily even when the occupants are out of station.

1.3                                             OBJECTIVE OF THE PROJECT
The objective of this work is to design a device that will trigger a lamp when darkness fall on the sensor (LDR).

1.4                                                 SCOPE OF THE PROJECT
A dark activated switch is an electronic  consisting of LDR, transistor and Relay as connected in the main circuit, as shown below.
The circuit shown below requires a DC voltage, which can be supplied from a battery or by using a bridge rectifier instead of the battery. The bridge rectifier uses a step-down transformer to step-down the 230v into 12v.
This circuit is to switch ON the light when the LDR is illuminated. The light dependent resistor will have high resistance in darkness and low resistance in the light. The comparator used here has LDR connected to its inverting terminal and potentiometer connected to its non-inverting pin.
When the darkness falls on the Light Dependent Resistor, the comparator compares the voltages at the reference pin that is with the non-inverting pin and the inverting pin of the op-amp. If the voltage at the non-inverting pin is greater than the voltage at the inverting pin the transistor cannot be switched. If the voltage at non-inverting pin is less than the voltage at the inverting pin, the output of the comparator can switch the transistor.

1.5                                         SIGNIFICANCE OF THE PROJECT
This device is very useful in that it distinguishes daylight and dark hours. This device eliminates the need of switching the Porch lamp or Backyard lamp daily and also helps to switch ON or OFF the premises of the house when the occupants are out of station.

1.6                                           LIMITATION OF THE PROJECT
One of the problems of this device is that any opaque material can trigger the device, such as human shadow, movement of animals or ants across the sensor can trigger the system 1.7                                 APPLICATIONS OF THE PROJECT
  • Useful for automatic outdoor lighting or garden lighting at home.
  • Useful for automatic switching of street lights.
  • Useful for switching the hoardings on and off automatically.
  • Useful for self-switching operation of displaying title hoardings of companies.
  • Useful as a light detector circuit when the pin of the ic is reconfigured.
  • Useful as a dark activated switch.
1.8                                         METHODOLOGY
To achieve the aim and objectives of this work, the following are the steps involved:
  • Study of the previous work on the project so as to improve it efficiency.
  • Draw a block diagram.
  • Test for continuity of components and devices,
  • Design of the device was carried out.
  • Studying of various component used in circuit.
  • Construction of the circuit was carried out. The construction of this project includes the placing of components on Vero boards, soldering and connection of components,
  • Finally, the whole device was cased and final test was carried out.
1.9                          PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to dark activated alarm. In this chapter, the background, significance, objective limitation and problem of dark activated alarm were discussed.
Chapter two is on literature review of dark activated alarm. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.

CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and construction of a dark activated switch using light dependent resistor" is also available. Order full work to download. Chapter two of "design and construction of a dark activated switch using light dependent resistor" consists of the literature review. In this chapter all the related works on "design and construction of a dark activated switch using light dependent resistor" were reviewed.

CHAPTER THREE: The complete chapter three of "design and construction of a dark activated switch using light dependent resistor" is available. Order full work to download. Chapter three of "design and construction of a dark activated switch using light dependent resistor" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of "design and construction of a dark activated switch using light dependent resistor" is available. Order full work to download. Chapter four of "design and construction of a dark activated switch using light dependent resistor" consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of design and construction of a "design and construction of a dark activated switch using light dependent resistor" is available. Order full work to download. Chapter five of "design and construction of a dark activated switch using light dependent resistor" consist of conclusion, recommendation and references.

 

CLICK HERE FOR MORE RELATED TOPICS/MATERIAL


To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions


For more information contact us through any of the following means:

Mobile No phonelogo:+2348146561114 or +2347015391124 [Mr. Innocent]

Email address emailus:engr4project@gmail.com

Watsapp No whatsapp.html :+2348146561114


COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp Nowhatsapp.html
:+2348146561114


E
mail Address emailus:engr4project@gmail.com


FOLLOW / VISIT US VIA:

tweeter instagram.htmlfacebook logomyyoutubelogo.html