USER'S INSTRUCTIONS: The project work you are about to view is on design and construction of a microcomputer trainer kit. Please, sit back and study the below research material carefully. This project topic (design and construction of a microcomputer trainer kit) have complete 5(five) Chapters . Each Project Material include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this design and construction of a microcomputer trainer kit project research material is to reduce the stress of moving from one school library to another all in the name of searching for design and construction of a microcomputer trainer kit research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
DESIGN AND CONSTRUCTION OF A MICROCOMPUTER TRAINER KIT
BY
---
EE/H2007/01430
DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
SCHOOL OF ENGINEERING
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work,design and construction of a microcomputer trainer kit by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on Electrical and Electronics Engineering has been approved.
By
Engr. --- Engr. ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
Engr. ---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work design and construction of a microcomputer trainer kit research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages ( use it to develop yours), Abstract and Chapter one of design and construction of a microcomputer trainer kit visible for everyone, then the complete material on design and construction of a microcomputer trainer kit is to be ordered for. Happy viewing!!!
The microcomputer revolution in electronics is spreading so rapidly it is difficult to educate enough people quickly and thoroughly in the new technology. Lawrence Livermore Laboratory's MST-80B was developed as a way to speed learning in our in-house training courses, and it is now being widely used outside LLL. The MST-80B trainer is a complete, self-contained, microcomputer system housed in a briefcase. The trainer uses the Intel 8080A* 8-Bit Microprocessor (CPU) , and it has its own sol i d-state memory, a built-in keyboard, input and output ports, and a display for visual output. The trainer is furnished with a permanent "Monitor" Program (in Read-Only Memory) that allows users to easily enter, debug, modify, and run programs of their own.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- OBJECTIVE OF THE PROJECT
- PURPOSE OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- APPLICATION OF THE PROJECT
- PROBLEM/LIMITATION OF THE PROJECT
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF MICROCOMPUTER
- ORIGINS OF MICROCOMPUTER
- HISTORICAL BACKGROUND OF THE STUDY
CHAPTER THREE
METHODOLOGY
- SYSTEM BLOCK DIAGRAM
- HARDWARE FEATURES OF THE TRAINER
- TRAINING MUDULE SUSSECTION USING SEVEN SEGMENT DISPLAY
- SYSTEM PICTURE
- FEATURES OF THE SYSTEM
- DESCRIPTION AND FUNCTION OF SEVEN SEGMENT DISPLAY
CHAPTER FOUR
TESTING AND RESULTS
- MONITOR PROGRAM
- SYSTEM KEYS FUNCTION
- MONITOR SUBROUTINES AS A CALL FROM A USER PROGRAM
CHAPTER FIVE
- CONCLUSION
- REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
Microcomputer trainer system is a complete microcomputer system self-contained in a briefcase for portability and easy usage. The microcomputer was designed as a training device for LLL' s Technology Training Program (TTP), a1 lowing students to explore the hardware and software capability of a typical microcomputer.
The trainer uses the Intel 8080A microprocessor and supporting integrated circuits. It has its own set of solid-state memory elements so no external memory is required. Both random-access read/write memory (RAM) and programmable read-only memory (PROM) are provided. The MST-80B has a 24-key keyboard and a 3-digit numerical display for the student to communicate with the microcomputer. This input/output (I/O) combination eliminates the need for expensive and bulky 1/0 such as a teletypewriter. The keyboard and numerical display can be used with either the octal (base 8) number system or the hexadecimal (base 16) number system. Either number system can be selected by simply depressing a control key. The trainer includes a breadboard socket so that experiment can be interfaced to the microcomputer through an 8-bit input port and an 8-bit output port. This allows the student to learn hardware Interfacing techniques as well as software programming. The MST-80B also has ten uncommitted light-emitting diodes (LEDs) that can easily be connected to display the state of any desired signals (address lines, data lines, and status). These can be used when operating the trainer in the single-step mode or the normal operating mode.
1.2 OBJECTIVE OF THE PROJECT
This objective of this work is study microcomputer training modules which display its output via seven segment display. It is a versatile microcomputer trainer used as an instructional aid in colleges and universities. It is a complete single board micro computer used for software and hardware development in research institutions.
1.3 PURPOSE OF THE PROJECT
A microcomputer is a complete computer on a small scale, designed for use by one person at a time. Smaller than a mainframe or minicomputer, a microcomputer uses a single integrated semiconductor chip for its central processing unit (CPU). This kit really had only one purpose - to wire up a little microprocessor that had a tiny bit of RAM and a very small instruction set built-in to a clock, LED displays, a keypad, speaker, and, of course, power, which was supplied by six AA batteries.
1.4 SIGNIFICANCE OF THE PROJECT
Microcomputer trainer is designed to provide further and more extensive studies about some important computer circuits. Microcomputer trainer wide range of most common computer application circuits that are used in computer.
Microcomputer training modules is a tool to allow Students and developers to have more knowledge of computers. It is a powerful and flexible system that provides a user friendly environment to carry out a large variety of programming application tasks. This module help students to understand the architecture and programming of computer.
With this trainer, Students edit and make a assembly program codes from PC and observe instant results after they download and execute programs from system memory. Debug functions are also available via PC or system keypad interface.
1.5 APPLICATION OF THE PROJECT
Microprocessor training module is used in:
- Design student programming projects
- Familiarize components used in microcomputer
- Learn the art of programming in machine language
- Design application oriented equipment
1.6 LIMITATION OF THE PROJECT
Microcomputer trainer system to do more work per unit time is to accept that they generate more heat, and somehow this power needs to be got in and then got out again. It is the latter which is causing the greater problems.
1.7 PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to microcomputer trainer kit. In this chapter, the background of microcomputer trainer kit, significance of a microcomputer trainer kit, scope of a microcomputer trainer kit, objective of a microcomputer trainer kit, limitation of a microcomputer trainer kit was discussed.
Chapter two is on literature review of the study. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
CHAPTER TWO: The complete chapter two of design and construction of a microcomputer trainer kit is available. Order full work to download. Chapter two of design and construction of a microcomputer trainer kitconsist of the literature review. In this chapter all the related work on design and construction of a microcomputer trainer kit was reviewed.
CHAPTER THREE: The complete chapter three of design and construction of a microcomputer trainer kit is available. Order full work to download. Chapter three of design and construction of a microcomputer trainer kit consist of the methodology design and construction of a microcomputer trainer kit. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of design and construction of a microcomputer trainer kit is available. Order full work to download. Chapter four of design and construction of a microcomputer trainer kit consist of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of design and construction of a microcomputer trainer kit is available. Order full work to download. Chapter five of design and construction of a microcomputer trainer kit consist of conclusion, recommendation and references of design and construction of a microcomputer trainer kit.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research for your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view more our related construction (or design) pics
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.