+234 8146561114 (MTN) or
+2347015391124 (AIRTEL)

DESIGN AND CONSTRUCTION OF A MICROCONTROLLER BASED WINDING MACHINE

USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a microcontroller based winding machine" Please, sit back and study the below research material carefully. This project topic "design and construction of a microcontroller based winding machine" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a microcontroller based winding machine" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a microcontroller based winding machine" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.


TITLE PAGE

DESIGN AND CONSTRUCTION OF A MICROCONTROLLER BASED WINDING MACHINE

BY

---
EE/H2013/01430
DEPARTMENT OF ---
INSTITUTE OF ---

DECEMBER,2018



APPROVAL PAGE

This is to certify that the research work, "design and construction of a microcontroller based winding machine" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on Electrical and Electronics Engineering has been approved.

By
Dr. ---                                           Dr. ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
Dr. ---
External Invigilator



DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.



ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.


PROJECT DESCRIPTION: This work “design and construction of a microcontroller based winding machine” research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of “design and construction of a microcontroller based winding machine” visible for everyone, then the complete material on “design and construction of a microcontroller based winding machine” is to be ordered for. Happy viewing!!!


ABSTRACT

In this project “microcontroller based automatic coil winding machine" main objective is to bring out a machine which can implement the idea of automation in Transformer winding or any type of coil windings. The proposed system controls the speed of a winding machine in order to obtain the optimum stop point in terms of security and fast production. The system is based on a microcontroller and an extremely simple hardware. The system has been tested for two years and results evince a very good mean time between failures.

 

 

 

 

TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
INTRODUCTION
1.1      BACKGROUND OF THE PROJECT

    1. PROBLEM STATEMENT
    2. PURPOSE OF THE PROJECT
    3. OBJECTIVE OF THE PROJECT
    4. SIGNIFICANCE OF THE PROJECT
    5. APPLICATION OF THE PROJECT
    6. TYPES OF COIL WINDING MACHINES
    7. DEFINITION OF TERMS
    8. PROJECT ORGANISATION

CHAPTER TWO
LITERATURE REVIEW

    1. OVERVIEW OF THE STUDY
    2. REVIEW OF DIFFERENT KINDS OF COIL
    3. TYPES OF WINDING MACHINE
    4. REVIEW OF AUTOMATIC COIL AND TRANSFORMER WINDING MACHINES

CHAPTER THREE
3.0      METHODOLOGY

    1. BASIS OF AN AUTOMATIC WINDING MACHINE
    2. AUTOMATIC COIL WINDER CONTROL UNIT SCHEMATIC DIAGRAMS
    3. PRINCIPLE OF OPERATION
    4. CONSTRUCTION NOTES
    5. POWER SUPPLY UNIT

CHAPTER FOUR
4.0      TEST AND RESULT ANALYSIS

    1. CONSTRUCTION PROCEDURE AND TESTING
    2. CASING AND PACKAGING
    3. ASSEMBLING OF SECTIONS
    4. TESTING OF SYSTEM OPERATION

CHAPTER FIVE

    1. CONCLUSION
    2. RECOMMENDATION
    3. REFERENCES

 

 

 

 

CHAPTER ONE
1.0                                                        INTRODUCTION
1.1                                         BACKGROUND OF THE PROJECT
Coil winding machine allows you to make an electromagnetic coil that can be used for a variety of purposes. A coil winding machine takes a copper or aluminum wire and winds it around a core or sometimes around air. The coils are usually wound around reels. During this process, the wires can be coated with a variety of materials that can provide some form of insulation. The types of wire, coiling, and insulation needed depends upon the particular application.
Automatic coil winding machine main objective is to bring out a machine which can implement the idea of automation in Transformer winding or any type of coil windings. A transformer changes (transforms) an alternating voltage from one value to another. It consists of two coils, called the primary and secondary winding, which are not connected electrically. The windings are either one on top of the other or are side by side on an iron, iron-dust or air core.
A transformer works by electromagnetic induction: a.c. is supplied to the primary and produces a changing (alternating) voltage in the secondary. It is important that as much as possible of the magnetic field produced by the primary passes through the secondary. A practical arrangement designed to achieve this in an iron-cored transformer. In which the secondary is wound on top of the primary. You should also notice that the induced voltage in the secondary is always of opposite polarity to the primary voltage.
Too large a current in a transformer causes magnetic saturation of the core i.e. the magnetization of the core is a maximum and it is no longer able to follow changes of magnetizing current. Particular care is required when there is a d.c. component.
In block consists of keypad, Microcontroller, display, Stepper motor, Stepper driver circuit, coil winding machine. This demo works on the basis that the keypad provided is for entering the set values that is the number of windings can be given In case of transformer the primary winding and secondary winding can be entered. All the interfacing with Microcontroller is done through its I/O lines.
The aim of this project is to develop a microcontroller based automatic coil winding machine to wind coils for Transformers, condensers, Coil rolls etc.  This machine is needed to wind coils of copper wires up to hundreds of gauges.  The operation of coil winding machine is performed automatically by microcontroller – which is the heart of the machine and by using a Motor – which controls the winding movement. 


1.2                                                  PROBLEM STATEMENT
Traditional or manual method of winding copper or aluminum wire waste much time, leads to miscalculation of number of coil ( which leads to under or over number of turns), and also can cause scratching the coat of the wire – which can cause flux leakage and electric shock during the device operation. The invention of an automatic winding machine led to overcoming these problems associated with the traditional method of winding coil.

1.3                                            OBJECTIVES OF THE PROJECT
The objective of this work is to construct a microcontroller winder which is used for winding copper or aluminum wire.

1.4                                              PURPOSE OF THE PROJECT
The purpose of this work is to have a fast, easy, displayable and reliable means of winding coils for Transformers, condensers, Coil rolls

1.4                                         SIGNIFICANCE OF THE PROJECT
This machine has the ability of UP or DOWN counting. In case number of turns is more than required value, the count can be reduced to required value by rotating the coil in reverse direction. The other advantage of an automatic winding machine are:

  1. It can greatly reduce employee fatigue strength, improve work efficiency, saving tie.
  2. PLC program control, text display set parameters, and easy operation.
  3. can adjust the length of the winding, winding coils set tie line length, number of laps setting   can yield count.
  4. for the AC power cord, DC power cord, USB data number, video cable, HDMI high-definition   cable, and other various types of transmission lines using plastic bag tied into bundles core twisted  purposes.

1.5                                          APPLICATION OF THE PROJECT

  1. It is very useful in Transformer manufacturing Company, to wind the transformer quickly.
  2. To wind the stator or rotor in motor or submersible pump company.
  3. To wind the condensers coil and fan coils quickly.
  4. It is very useful in small scale industries where ever winding coils are used.

1.6                                    TYPES OF COIL WINDING MACHINES

There are different types of coil winding machines available.

Coil Winders

Coil winders are generally used for smaller jobs. They can be hand operated or have a winding drive that is controlled by a foot pedal. These coil winding machines are used in the production of solenoid coils, multi-section coils, and other such complex coils. Though they are small, they can reach up to speeds of 9000 RPM.

Medium-Duty Coil Winding Machines

These machines are more powerful than coil winders and take on higher production demands. Most of them are driven by potentiometers. They can wind various types of wires.

Heavy-Duty Coil Winding Machines

Heavy-duty motor coil winding machines are able to take care of extremely large amounts and are also very versatile in nature. For higher precision, most of these machines are equipped with LCD touch-screen monitors. These screens allow operators to have more control over speed.

1.7                                                  DEFINITION OF TERMS
COIL(s): The end result of a wire, tube, or bar in a continuous loop referred to as "turn" to create a Helix spiral.
 COIL ASSEMBLY: Is when parts (ex: plastic) are added to the coil to be considered complete.
 COIL BENDING: Is when the end of a coiled material is curved or bent in different directions.
 COIL WINDING: "coil" in this sense refers to the wire or conductor and "winding" is the turn/loop of the wire to create the end result.
Over Winding: The winding of a second coil on top of another coil.
TOROIDS: Is a ring-shaped core that can be made of ferrite (magnetic) or out of dust-iron that is used to wind wires inductors.
 TOROID COIL: Is sometimes known as "Toroid Inductor" and is used for low frequencies.  It is a coil that is wire wound on a toroid.
TUBE BENDING: Is when a hollow tube of various sizes and material (such as copper) is bent to form a specific shape.  The tube can be curved or angled to create a unique shape based on the functionality and need of the project. The tube size and thickness can vary to ensure the curve or angle follows the original OD of the tube.
TUBE WINDING: Is when a hollow tube of various sizes and material (such as copper) are wound in a continuous loop/turn. A coil is created when tube is wound on a custom mandrel creating a spiral like shape with or without spacing, thus creating a coil. These tubes are utilized in many different industries to create a path for energy or used to heat or cool liquid.
 TURNS:  Is the number of loops in a coil(s).

1.9                                        PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to a microcontroller based winding machine. In this chapter, the background, significance, objective limitation and problem of a microcontroller based winding machine were discussed.
Chapter two is on literature review of a microcontroller based winding machine. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.

CHAPTER ONE: The complete chapter one of “design and construction of a microcontroller based winding machine” is available. Order full work to download. Chapter one of “design and construction of a microcontroller based winding machine”consists of the literature review. In this chapter all the related work on“design and construction of a microcontroller based winding machine” was reviewed.

CHAPTER TWO: The complete chapter two of “design and construction of a microcontroller based winding machine” is available. Order full work to download. Chapter two of “design and construction of a microcontroller based winding machine” consists of the literature review. In this chapter all the related work on “design and construction of a microcontroller based winding machine” was reviewed.

CHAPTER THREE: The complete chapter three of “design and construction of a microcontroller based winding machine” is available. Order full work to download. Chapter three of “design and construction of a microcontroller based winding machine” consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of “design and construction of a microcontroller based winding machine” is available. Order full work to download. Chapter four of “design and construction of a microcontroller based winding machine” consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of “design and construction of a microcontroller based winding machine” is available. Order full work to download. Chapter five of “design and construction of a microcontroller based winding machine” consist of conclusion, recommendation and references.



To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

You can also visit our facebook Page at fb.me/hyclas to view our related construction (or design) picture.


For more information contact us through Any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.


COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No
:+2348146561114

E
mail Address :engr4project@gmail.com


CLICK HERE FOR MORE RELATED TOPICS/MATERIAL

IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.