DESIGN AND CONSTRUCTION OF A MOBILE PHONE CALL INDICATOR
USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a mobile phone call indicator" Please, sit back and study the below research material carefully. This project topic "design and construction of a mobile phone call indicator" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a mobile phone call indicator " project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a mobile phone call indicator" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
DESIGN AND CONSTRUCTION OF A MOBILE PHONE CALL INDICATOR
BY
---
EE/H2013/01430
DEPARTMENT OF ---
SCHOOL OF --
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work, "design and construction of a mobile phone call indicator" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a B.Sc on --- has been approved.
By
Dr. --- Dr. ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
Dr. ---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work “design and construction of a mobile phone call indicator” research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of “the rate and causes of infant mortality in edo state (case study of irrua specialist teaching hospital)” visible for everyone, then the complete material on “the rate and causes of infant mortality in edo state (case study of irrua specialist teaching hospital)” is to be ordered for. Happy viewing!!!
This work is titled design and construction of a Mobile phone call indicator. Mobile phone call indicator is a device that flashes an LED when it detects an incoming call.
Mobile phone call indicator can be used to escape from the nuisance of mobile phone rings when you are at home. This circuit will give a visual indication if placed near a mobile phone even if the ringer is deactivated. This circuit was designed to detect when a call is incoming in a cellular phone (even when the calling tone of the device is switched-off) by means of a flashing LED.
The device must be placed a few centimeters from the cellular phone, so its sensor coil L1 can detect the field emitted by the phone receiver during an incoming call.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
- INTRODUCTION
- BACKGROUND OF THE PROJECT
- PROBLEM STATEMENT
- OBJECTIVE OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- SCOPE OF THE PROJECT
- LIMITATION OF THE PROJECT
- APPLICATION OF THE PROJECT
- METHODOLOGY
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- REVIEW OF TELEPHONE CALL
CHAPTER THREE
METHODOLOGY
- SYSTEM BLOCK DIAGRAM
- CIRCUIT DIAGRAM
- SYSTEM OPERATION
- CIRCUIT DESCRIPTION
- PARTS LIST
- DESCRIPTION OF MAJOR COMPONENTS USED
CHAPTER FOUR
4.0 TEST AND RESULT ANALYSIS
- CONSTRUCTION PROCEDURE AND TESTING ANALYSIS
- CASING AND PACKAGING
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- INSTALLATION OF THE COMPLETED DESIGN
- RESULTS AND DISCUSSION
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE STUDY
This project is designed to help escape from nuisance of incoming call at home, offices and during conferences. The circuit is designed to give a visual indication if placed near a mobile phone even if the ringer is deactivated.
This circuit was designed to detect when a call is incoming in a cellular phone (even when the calling tone of the device is switched-off) by means of a flashing LED.
This handy, pocket-size mobile incoming call detector or sniffer can sense the presence of an activated mobile cell phone from a distance of one and-a-half meters. So it can be used to prevent use of mobile phones in examination halls, confidential rooms, etc. It is also useful for detecting the use of mobile phone for Spying and unauthorized video transmission. The circuit can detect the incoming and outgoing calls, SMS and video transmission even if the mobile phone is kept in the silent mode.
When a call is coming to the mobile phone, the transmitter inside it becomes activated. The frequency of the transmitter is around 900MHZ. The coil picks up these oscillations by induction and feds it to the base of the transistor. This make the transistor activated. Since the collector of transistor is connected to the pin 2 NE555, the IC1 is triggered to make the LED connected at its output pin to blink. The blinking of the LED is the indication of incoming call. The circuit must be powered by a 6V battery.
1.2 PROBLEM STATEMENT
Phones ringing tone causes noise pollution and distraction most especially when it is used in an unwanted places such as conference hall, examination hall or any other public places where silence is needed. In order to solve this problem, this device is used. When using this device and a new call comes, this circuit will provide you an optical effect by flashing an LED. It can be useful in situations where you can’t keep your phone on ringing mode like while working in the office or at home when somebody is sleeping or even when you don’t wish to hear the tone and need some silence. This circuit can also be used in places where there is a lot of noise due to which you are not able to hear the ringtone of your cell phone
1.3 OBJECTIVE OF THE PROJECT
The objective of this project is to design a device that will detect when a call is incoming in a cellular phone
1.4 SIGNIFICANCE OF THE PROJECT
1. Whenever you have a new call this project will provide you a visual warning.
2. This circuit is very useful at noisy places where it’s difficult to hear the ringtone.
3 When you are fed up of incoming calls and need silence but cannot ignore ringtone, this circuit would be useful. You will get new call information by a blink of LED.
4. You need to put your mobile close to this project and LED will blink when you have a call. This project will detect the radiation coming out from your mobile.
1.5 SCOPE OF THE PROJECT
The system was built using a 555 timer IC, coil, pickup antenna and so many other electronics components. The most important part of the circuit is a 130-150 turn coil, which acts as a pick-up antenna for a signal that is emitted by your mobile phone whenever it has an incoming coil. The signal induced in this coil/inductor is amplified through a transistor, which is then used to drive a monostable 555 Timer. The output voltage of the IC is used to drive a ultra-bright LED.
1.6 LIMITATION OF THE PROJECT
This project operates with battery, which means that the system will stop working whenever the battery runs down.
1.7 APPLICATION OF THE PROJECT
This device was designed to be used in places where noise is highly prohibited such as:
- conferences hall
- exam hall
- worship places
- banks, etc.
1.8 METHODOLOGY
To achieve the aim and objectives of this work, the following are the steps involved:
- Study of the previous work on the project so as to improve it efficiency.
- Draw a block diagram.
- Test for continuity of components and devices,
- Design and calculation for the device was carried out.
- Studying of various component used in circuit.
- Construction of the circuit was carried out.
- Finally, the whole device was cased and final test was carried out.
1.9 PROJECT ORGANISATION
The work is organized as follows: chapter one discuses the introductory part of the work, chapter two presents the literature review of the study, chapter three describes the methods applied, chapter four discusses the results of the work, chapter five summarizes the research outcomes and the recommendations.
CHAPTER TWO: The complete chapter two of “design and construction of a mobile phone call indicator” is available. Order full work to download. Chapter two of “design and construction of a mobile phone call indicator” consists of the literature review. In this chapter all the related work on “design and construction of a mobile phone call indicator"
CHAPTER THREE: The complete chapter three of “design and construction of a mobile phone call indicator” is available. Order full work to download. Chapter three of “design and construction of a mobile phone call indicator” consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of "design and construction of a mobile phone call indicator” is available. Order full work to download. Chapter four of “design and construction of a mobile phone call indicator” consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of design and construction of a “design and construction of a mobile phone call indicator” is available. Order full work to download. Chapter five of “design and construction of a mobile phone call indicator” consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view our related construction (or design) picture.
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.