An FM transmitter is an electronic device which, with the aid of an antenna, produces radio waves. The transmitter itself generates a radio frequency alternating current, which is applied to the antenna. When excited by this alternating current, the antenna radiates radio waves.
FM transmitter is basically a VHF colipits oscillator capable of transmitting sound or music to any standard FM receiver. The circuit works on a D.C source which makes it for a pure rectification. FM transmitter also has a capacitor microphone which picks up very weak sound signals.
The FM transmitter was designed using transistors and other component such resistor, inductor and capacitors. This project transmits frequency on 100MHz± 5%. The transmitting distance is l00metres. It is powered with 5volt – 15volts D.C battery using suitable F.M receiver tuned to the transmitting frequency of this project. F.M Transmitter can be used as cordless microphones, mobile phone and for public address purposes. The distant of transmission is limited to 100m and fixed frequency of transmission, away from all other radio station. This gives best range and least interference.
TABLE OF CONTENTS
TABLE OF CONTENT
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT
CHAPTER ONE
1.0 INTRODUCTION
1.1 PURPOSE OF THE PROJECT
1.2 OBJECTIVE OF THE PROJECT
1.3 LIMITATIONS OF THE PROJECT
1.4 APPLICATION OF THE PROJECT
1.5 SIGNIFICANCE OF THE PROJECT
1.6 DEFINITION OF TERMS
CHAPTER TWO
2.0 LITERATURE REVIEW
2.1 HISTORITICAL BACKGROUND OF THE PROJECT
2.2 REVIEW OF PARTS OF RADIO TRANSMITTER
2.3 REVIEW OF FM BROADCAST BANDS
2.4 MODULATION AND DEMODULATION
2.5 PRE-EMPHASIS AND DE-EMPHASIS
2.6 REVIEW OF MODULATION CHARACTERISTICS
CHAPTER THREE
3.0 CONSTRUCTION
3.1 BASICS OF FM TRANSMITTER
3.2 BLOCK DIAGRAM OF AN FM TRANSMITTER
3.3 FUNCTION OF FM TRANSMITTER BLOCK
3.4 CIRCUIT DIAGRAM OF THE SYSTEM
3.5 CIRCUIT PARTS
3.6 CIRCUIT OPERATION
3.7 DESCRIPTION OF COMPONENTS USED
CHAPTER FOUR
4.0 RESULT ANALYSIS
4.1 CONSTRUCTION PROCEDURE AND TESTING
4.2 CASING AND PACKAGING
4.3 ASSEMBLING OF SECTIONS
4.4 TESTING OF SYSTEM OPERATION
4.5 INSTALLATION OF THE COMPLETED DESIGN
4.6 SYSTEM TROUBLESHOOTING METHOD
4.7 COST ANALYSIS
CHAPTER FIVE
5.0 CONCLUSION
5.1 RECOMMENDATION
5.2 BIBLIOGRAPHY
CHAPTER ONE
1.0 INTRODUCTION
In electronics and telecommunications a radio fm transmitter is an electronic device which, with the aid of an antenna, produces radio waves. The transmitter itself generates a radio frequency alternating current, which is applied to the antenna. When excited by this alternating current, the antenna radiates radio waves. In addition to their use in broadcasting, transmitters are necessary component parts of many electronic devices that communicate by radio, such as cell phones, wireless computer networks, Bluetooth enabled devices, garage door openers, two-way radios in aircraft, ships, and spacecraft, radar sets, and navigational beacons. The term transmitter is usually limited to equipment that generates radio waves for communication purposes; or radiolocation, such as radar and navigational transmitters. Generators of radio waves for heating or industrial purposes, such as microwave ovens or diathermy equipment, are not usually called transmitters even though they often have similar circuits.
The term is popularly used more specifically to refer to a broadcast transmitter, a transmitter used in broadcasting, as in FM radio transmitter. This usage usually includes the transmitter proper, the antenna, and often the building it is housed in.
A transmitter can be a separate piece of electronic equipment, or an electrical circuit within another electronic device. A transmitter and receiver combined in one unit is called a transceiver. The term transmitter is often abbreviated "XMTR" or "TX" in technical documents. The purpose of most transmitters is radio communication of information over a distance. The information is provided to the transmitter in the form of an electronic signal, such as an audio (sound) signal from a microphone. The transmitter combines the information signal to be carried with the radio frequency signal which generates the radio waves, which is often called the carrier. This process is called modulation. The information can be added to the carrier in several different ways, in different types of transmitter.
In a frequency modulation (FM) transmitter, it is added by varying the radio signal's frequency slightly. Many other types of modulation are used.
The antenna may be enclosed inside the case or attached to the outside of the transmitter, as in portable devices such as cell phones, walkie-talkies, and garage door openers. In more powerful transmitters, the antenna may be located on top of a building or on a separate tower, and connected to the transmitter by a feed line, that is a transmission line.
1.1 PURPOSE OF THE PROJECT
The main purpose of this work is to construct a device that will allow music or other audio content from a portable media player, CD player or other portable audio system to be played through a nearby FM radio. It can either be a capability built into a portable media player, or a portable appliance that plugs into the headphone jack or proprietary output port of a portable media player or video device. The sound is then broadcast through the transmitter on an FM broadcast band frequency and picked up by the receiver. The purpose is generally to allow portable audio devices to make use of the better sound quality of a home audio system or car stereo without requiring a wired connection between them.
The FM transmitter plugs into the audio output of audio devices and converts the audio output into an FM radio signal, which can then be picked up by appliances such as car or portable radios.
1.2 OBJECTIVE OF THE PROJECT
- The objective of this work is to design and construct a long range FM transmitter which transmits a frequency modulated signal to an fm radio. That is, to construct a device that can broadcast signals on an FM broadcast band and picked up by the receiver.
- To review some modern digital technologies that has been developed for effective FM signal generation.
- To show the design and components of a FM transmitter
- To show the construction process of an electronically operated system known as FM transmitter capable of transmitting a frequency modulated signal.
The relatively low power output of FM transmitters sometimes makes it unsuitable for use in some large urban areas because of the number of other radio signals. This is compounded by the fact that strong FM signals can bleed over into neighboring frequencies making the frequencies unusable with the transmitter. Removing a car’s radio antenna has been found to significantly improve transmitter reception. Some frequencies below 88.1 have even been supported as reception frequencies on some car stereos, and some indegeneous FM transmitters even take advantage of those unused frequencies which are generally more reliable as no frequency below 88.1 is used for mainstream broadcasters.Some models which connect via ports other than the headphone jack have no means of controlling the volume, which can force the sound to transmit out from the device harshly (causing over modulation, audio distortion and possible radio interference), or too low. In theory a device could use an automatic level control or audio limiter circuit to overcome this problem although there are few (if any) devices with such a facility available out on the market yet.
1.4 APPLICATION OF THE PROJECT
FM transmitters used in many different environments. Some of the more popular uses are churches, sporting events, fitness centers, homes, cars, correctional facilities and holiday light shows. Other applications include
• Non-commercial broadcasting.
• Commercial broadcasting.
• Television audio.
• Public Service communications.
• Radio Service Communications.
• Point-to-point microwave links used by telecommunications companies.
1.5 SIGNIFICANCE OF THE STUDY
The project signifies a lot in the electronic communication system which telecommunication is the vital aspect which is usually demonstrated through radio communication system the frequency modulation transmitter is applied in a lot of instance frequency modulation is used in FM radio stations scattered all over the country whose advantage is paramount compared to its counterpart AM modulation frequency modulation transmitted is equally used in a miniaturized from as wireless morpheme.
1.6 DEFINITION OF TERMS
FM – Frequency Modulation
VHF – Very High Frequency (30MHz to 300MHz)
UHF – Ultra High Frequency (300MHz to 3GHz)
VFO – Variable Frequency Oscillator
VCO – Voltage Controlled Oscillator
PLL – Phase Locked Loop
Oscillator – device that generates a frequency
This material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We make abstract and chapter one visible for everyone.
All Project Topics on this site have complete 5(five) Chapters . Each Project Material include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
To view other related topics click HERE
To "SUMMIT" new topic(s) OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research for your new topic? if yes, click "HERE"
For more information call us on:+2348146561114 (MTN) or +2347015391124 (AIRTEL)
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.