USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v". Please, sit back and study the below research material carefully. This project topic "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
BY
---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---
APPROVAL PAGE
This is to certify that the research work, "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.
By
--- . ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" visible for everyone, then the complete material on "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" is to be ordered for. Happy viewing!!!
TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT
CHAPTER ONE
- INTRODUCTION
- BACKGROUND OF THE PROJECT
- STATEMENT OF PPROBLEM
- AIM/OBJECTIVE OF THE PROJECT
- SCOPE OF THE PROJECT
- RESEARCH QUESTION
- APPLICATION OF THE PROJECT
CHAPTER TWO
LITERATURE REVIEW
2.1 REVIEW OF RECTIFIER DEVICES
2.2 RECTIFIER CIRCUITS
2.3 REVIEW OF REGULATED POWER SUPPLY
2.4 REVIEW OF POWER SUPPLY CHARACTERISTICS
2.5 REVIEW OF GENERAL APPLICATION OF POWER SUPPLY APPLICATIONS
2.6 REVIEW OF TYPES OF POWER SUPPLY
CHAPTER THREE
3.0 METHODOLOGY
3.1 SYSTEM BLOCK DIAGRAM
3.2 SYSTEM CIRCUIT DIAGRAM
3.3 CIRCUIT OPERATION
3.3 CIRCUIT PARTS
CHAPTER FOUR
4.0 RESULT ANALYSIS4.1 CONSTRUCTION PROCEDURE AND TESTING
4.2 ASSEMBLING OF SECTIONS
4.3 CONSRUCTION OF THE CASING
4.4 TESTING OF SYSTEM OPERATION
4.5 OBSERVATIONS
CHAPTER FIVE
- CONCLUSIONS
5.2 REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE STUDY
A rectifier is an electrical device that converts alternating current (AC), which periodically reverses direction, to direct current (DC), which flows in only one direction. A Rectifier converts AC (alternating current) to DC (direct current) The rectifier circuit takes alternating current (AC)and converts it into a positive direct current
(DC) output. Many power supplies, such as standard electrical output, produce AC voltage. Many handheld tools and other devices use DC. The rectifier is to provide desired DC power for the application.
Physically, rectifiers take a number of forms, including vacuum tube diodes, wet chemical cells, mercury-arc valves, stacks of copper and selenium oxide plates, semiconductor diodes, silicon-controlled rectifiers and other silicon-based semiconductor switches. Historically, even synchronous electromechanical switches and motor-generator sets have been used. Early radio receivers, called crystal radios, used a "cat's whisker" of fine wire pressing on a crystal of galena (lead sulfide) to serve as a point-contact rectifier or "crystal detector".
Rectifiers have many uses, but are often found serving as components of DC power supplies and high-voltage direct current power transmission systems. Rectification may serve in roles other than to generate direct current for use as a source of power. As noted, detectors of radio signals serve as rectifiers. In gas heating systems flame rectification is used to detect presence of a flame.
Depending on the type of alternating current supply and the arrangement of the rectifier circuit, the output voltage may require additional smoothing to produce a uniform steady voltage. Many applications of rectifiers, such as power supplies for radio, television and computer equipment, require a steady constant DC voltage.
To obtain a complete circuit for this work, the circuit is mainly composed of the:
Input transformer: The input transformer is used to transform the incoming line voltage down to the required level for the power supply. Typically the input transformer provides a step down function. It also isolates the output circuit from the line supply.
Rectifier: The power supply rectifier converts the incoming signal from an AC format into raw DC. Either half wave or more commonly full wave rectifiers may be used as they make use of both halves of the incoming AC signal.
Smoothing: The raw DC from the rectifier is far from constant falling to zero when the AC waveform crossed the zero axis, and then rising to its peak. The addition of a reservoir capacitor here fills in the troughs in the waveform, enabling the next stage of the power supply to operate. Large value capacitors are normally used within this stage.
Regulator: This stage of the power supply takes the smoothed voltage and uses a regulator circuit to provide a constant output virtually regardless of the output current and any minor fluctuations in the input level. In these applications the output of the rectifier is smoothed by an electronic filter, which is capacitor, followed by a voltage regulators to produce a steady voltages of 6, 12 and 15v, which is the main aim of this work.
1.2 PROBLEM STATEMENT
In many electronics projects, we see that there is a requirement of fixed-voltage power supply, fixed means no fluctuation in voltage. The output of any circuit fully depends on input voltage supply and it should be constant. Any sensitive circuit is more essential to operate on regulated power than any normal circuit. If I use RF operation in any circuit then its frequency must be constant because there is a small bit of voltage and current fluctuation make more variation of the output signal. We use the voltage regulator to regulate the voltage supply which maintains constant supply. 220 ac to 15v/12v/6v DC Regulated Power DC converter Bridge Rectifier as required.
1.3 AIM AND OBJECTIVES OF THE STUDY
The main aim of this work is to build a rectified power supply of multiple outputs of 6, 12 and 15v. The objectives are:
- To build the prototype of the system
- To have a power supply with multiple outputs of 6, 12 and 15v
- To have a wider knowledge of rectifier used for power supply application.
- To use the voltage regulator to regulate the voltage supply which maintains constant supply.220/230v ac to 15v/12v/6v DC Regulated Power DC converter Bridge Rectifier as required.
1.4 SCOPE OF THE STUDY
A rectifier circuit converts the Alternating Current (AC) input power into a Direct Current (DC) output power. The scope of this study covers building a rectified power supply of multiple out which was built around a step down transformer, a filter (capacitor), three different rating regulator (6, 12, and 15v). The complete work was built to generate a voltage of 6, 12 and 15v.
1.5 RESEARCH QUESTIONS
At the end of the day, answers to the following questions shall be provided:
- What is a rectifier and its types?
- What is a rectifier used for?
- What is rectifier and its principle?
- Why rectifier is used in power supply?
- Which rectifier is generally used in DC power supply?
1.6 APPLICATION OF RECTIFIERS
The primary application of rectifiers is to derive DC power from an AC supply (AC to DC converter). Rectifiers are used inside the power supplies of virtually all electronic equipment. AC/DC power supplies may be broadly divided into linear power supplies and switched-mode power supplies. In such power supplies, the rectifier will be in series following the transformer, and be followed by a smoothing filter and possibly a voltage regulator.
CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" is also available. Order full work to download. Chapter two of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" consists of the literature review. In this chapter all the related work on "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" was reviewed.
CHAPTER THREE: The complete chapter three of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" is available. Order full work to download. Chapter three of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" is available. Order full work to download. Chapter four of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" is available. Order full work to download. Chapter five of "design and construction of a rectified power supply with multiple output of 6v, 12v and 15v" consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
For more information contact us through any of the following means:
Mobile No 
:+2348146561114 or +2347015391124 [Mr. Innocent]
Email address 
:engr4project@gmail.com
Watsapp No 
:+2348146561114
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
FOLLOW / VISIT US VIA:
