DESIGN AND CONSTRUCTION OF A SIMPLE DYNAMO
USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a simple dynamo" Please, sit back and study the below research material carefully. This project topic "design and construction of a simple dynamo" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a simple dynamo" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a simple dynamo" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
DESIGN AND CONSTRUCTION OF A SIMPLE DYNAMO
BY
---
EE/H2013/01430
DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
SCHOOL OF ENGINEERING
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work, "design and construction of a simple dynamo" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on Electrical and Electronics Engineering has been approved.
By
Engr. --- Engr. ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
Engr. ---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work “design and construction of a simple dynamo” research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of “design and construction of a simple dynamo” visible for everyone, then the complete material on “design and construction of a simple dynamo” is to be ordered for. Happy viewing!!!
Dynamo is the name given to D.C generators. In the past, alternating current generators are not common. Voltages are generated using dynamo where the voltage generated are later converts to A.C. The dynamo I constructed had a permanent magnet. This magnet in the form of circular disc which revolves around turns of coil that is wound on a u-shaped former. When the disc is rotated the magnetic field North / South pole cuts lines of force and e.m.f is generated.
TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
- PURPOSE OF THE PROJECT
- AIM OF THE PROJECT
- OBJECTIVE OF THE PROJECT
- PURPOSE OF THE PROJECT
- LIMITATION OF THE PROJECT
- ADVANTAGES OF THE PROJECT
- PROBLEM OF THE PROJECT
- APPLICATION OF THE PROJECT
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
- OVERVIEW OF THE STUDY
- REVIEW OF THE RELATED STUDY
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BASIC OF THE SYSTEM
3.2 BLOCK DIAGRAM OF THE SYSTEM
3.3 SYSTEM OPERATION
3.4 CIRCUIT DIAGRAM
3.5 CIRCUIT DESCRIPTION
3.6 DESCRIPTION OF COMPONENTS USED
3.7 POWER SUPPLY UNIT
CHAPTER FOUR
4.0 TESTING AND RESULTS
- CONSTRUCTION PROCEDURE AND TESTING
- INSTALLATION OF THE COMPLET DESIGN
- ASSEMBLING OF SECTIONS
- TESTING OF SYSTEM OPERATION
- COST ANALYSIS
CHAPTER FIVE
- CONCLUSION
- RECOMMENDATION
- REFERENCES
1.0 INTRODUCTION
A dynamo is an electrical generator that creates direct current using a commutator. Dynamos were the first electrical generators capable of delivering power for industry, and the foundation upon which many other later electric-power conversion devices were based, including the electric motor, the alternating-current alternator, and the rotary converter. Today, the simpler alternator dominates large scale power generation, for efficiency, reliability and cost reasons. A dynamo has the disadvantages of a mechanical commutator. Also, converting alternating to direct current using power rectification devices (such as vacuum tubes or more recently via solid state technology) is effective and usually economical.The electric dynamo uses rotating coils of wire and magnetic fields to convert mechanical rotation into a pulsing direct electric current through Faraday's law of induction. A dynamo machine consists of a stationary structure, called the stator, which provides a constant magnetic field, and a set of rotating windings called the armature which turn within that field. Due to Faraday's law of induction the motion of the wire within the magnetic field creates an electromotive force which pushes on the electrons in the metal, creating an electric current in the wire. On small machines the constant magnetic field may be provided by one or more permanent magnets; larger machines have the constant magnetic field provided by one or more electromagnets, which are usually called field coils.
1.1 BACKGROUND OF THE STUDY
The word Dynamo from “(from the Greek word dynamics: meaning power) was originally another name for an electrical generator and still has some regional usage as a replacement for the word generator. After the discovery of the AC generator and that alternating current can be used as a power supply. The word dynamo became associated exclusively with the communicated direct current electric generator while on AC electrical generator using either ship rings or rotor magnet would become known as an alternator.A dynamo is an electrical generator that produces direct current with the use of a commutator. Dynamos were the first electrical generators capable of delivering power for industry and the foundation upon which many other later electric power conversion devices were based including the electric motor, the alternating current alternator and the rotary converter. Today the simple alternator dominates large scale power generation for efficiency, reliability and cost reasons.A dynamo has the disadvantages of a mechanical commutator besides; converting alternating current to direct current using power rectification devices (vacuum tube or more recently solid state.) is effective and usually economical.The faraday disk was the first electric generator. the horseshoe shape magnet (A) created a magnetic field through the disk (D) when the disk centers toward the rim. The current flowed out through the sliding spring contact m, through the external circuit and back into the centre of the disk through the axle. The operating principle of electromagnetic generators was later called Faraday’s law, is that an electromotive force is generated in an electrical conductor which encircles a varying magnetic flux. He also built the first electromagnetic generator, called the Faraday- disk, a type of homopolar generator, using a copper disk rotating between the poles of a horseshoe magnetic. It produced a small DV voltage. This was not a dynamo in the current sense, because it did not use a commutator. This design was inefficient, due to self counseling counter flows of current in regions that were not under the influence of the magnetic field. While current was induced directly underneath the magnet, the current would circulate backwards in regions that were outside the influence of the magnetic field. This counter flow limited the power output to the pickup wires and induced waste heating the copper disk later, homopolar generators would solve the problem by using an array of magnets arranged around the disk perimeter to maintain a steady field effect in one current flow direction.
Another disadvantage was the output voltage was very low, due to the single current path through the magnetic flux. Faraday and others found that higher, more useful voltages could be produced by winding multiple turns of wire into coil. Wire windings can conveniently produce any voltage desired by changing the number of turns? So they have commutator to produce direct current. Independently of Faraday, (The Hungarian) Anyas Jedlik started experimenting in (1827) with the electromagnetic rotating devices which he called electromagnetic self-rotors. In the prototype of the single pole electric starter, both the stationary and the revolving parts were electromagnetic.About 1856 he formulated the concept of the dynamo about six years before Siemens and Wheatstone but did not patent it as he thought he was not the first to realize this. His dynamo used, instead of permanent magnets, two electromagnets placed opposite to each other to induce the magnetic field around the rotor, it was also the discovery of the principle of dynamo self excitation.
1.2 STATEMENT OF PROBLEM
Before the connection between magnetism and electricity was discovered, electrostatic generators were used. They operated on electrostatic principles such generator generated very high voltage and low current. They operated by using moving electrically charged belts. The charge was generated using either of two mechanisms. Electrostatic induction and the turboelectric effect. Because of their inefficiency and the difficulty of insulating machines that produced very high voltages, electrostatic generators had low power ratings and were never used for generation of commercially significant quantities of electric power.
Currently, the negative impact of fossil fuel to our environment and the increasing rate of global warming and green house gases has made our environment unsafe and these is need to look for an alternative source of energy from natural source that can be environmentally friendly and yet still solve the energy need to our population. Also the epileptic power supply in developing countries has necessitated for another power source that will be constant and readily available.
1.3 AIM AND OBJECTIVE OF THE STUDY
The principle of operation and the technical know-how of simple dynamo helped a lot in the application an construction of wind turbine and the larger hydro-electric that has contributed immensely to the generation of very huge electrical power source to the national grid source. The objective of this project was to design and construct a simple dynamo using as far as possible locally available materials which would provide cheap means of generating energy to power source of our electronics. The objectives of the project therefore are to design and construct a simple dynamo from electromagnetic induction mechanism.
1.4 SIGNIFICANCE OF THE STUDY
The work will help solve the energy need of our society as it will generate alternative energy source. Specifically, many people benefit from this work as it provide simple, mobile and alternative sources of power to cyclist, part of camps at any given time or place.
Finally, this work has help to enlighten the society on how to utilize locally available electronics in construction of dynamos for the production of light.
1.5 SCOPE OF STUDY
This work will try to design and construct a simple dynamo using simple electronic components readily available in our local markets. Dynamo is made up of a copper coil and a magnet, It converts mechanical ( kinetic ) energy into electric energy , where the kinetic energy moves the copper coil between the two poles of the magnet to produce the electricity .
The electric current can be generated in a coil of dynamo by moving the coil in the magnetic field ( between the two poles of a magnet and by moving a magnet inside the coil .
The generation of the electric current in the coil increases by increasing the motion of the coil between the two poles of magnet .
1.6 USES AND APPLICATION OF THE STUDY
Electric power generation: Dynamos, usually driven by steam engines, were widely used in power stations to generate electricity for industrial and domestic purposes. They have since been replaced by alternators. Large industrial dynamos with series and parallel (shunt) windings can be difficult to use together in a power plant, unless either the rotor or field wiring or the mechanical drive systems are coupled together in certain special combinations. It seems theoretically possible to run dynamos in parallel to create induction and self sustaining system for electrical power. Transport: Dynamos were used in motor vehicles to generate electricity for battery charging. An early type was the third-brush dynamo. They have, again, been replaced by alternators. Modern uses: Dynamos still have some uses in low power applications, particularly where low voltage DC is required, since an alternator with a semiconductor rectifier can be inefficient in these applications. Hand cranked dynamos are used in clockwork radios, hand powered flashlights, mobile phone chargers, and other human powered equipment to recharge batteries.
1.7 ADVANTAGES OF A SIMPLE DYNAMO
1. Dynamos have no running cost. That means one bought they do not any running cost.
2. The power from the dynamo do not run out. As long as the bicycle is moving there will be enough lighting.
3. It environmental friendly. Dynamo do not use toxic chemicals to dispose.
1.8 PROBLEM OF THE STUDY
1. There can only be light if the bicycle is moving. Before the rider starts moving there is not light at all.
2. Whenever the speed reduces the light becomes dimmer. This means the rider has to maintain a certain speed for there to be enough light.
3. It require energy from the rider for there to be light. He has to keep on pending to maintain the motion of the bicycle.
1.9 PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to this study. In this chapter, the background, significance, scope, objective, the need (benefit), limitation and problem, advantages of this work was discussed.
Chapter two is on literature review of the study. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
CHAPTER TWO: The complete chapter two of “design and construction of a simple dynamo” is available. Order full work to download. Chapter two of “design and construction of a simple dynamo” consists of the literature review. In this chapter all the related work on “design and construction of a simple dynamo” was reviewed.
CHAPTER THREE: The complete chapter three of “design and construction of a simple dynamo” is available. Order full work to download. Chapter three of “design and construction of a simple dynamo” consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of “design and construction of a simple dynamo” is available. Order full work to download. Chapter four of “design and construction of a simple dynamo” consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of design and construction of a “design and construction of a simple dynamo” is available. Order full work to download. Chapter five of “design and construction of a simple dynamo” consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view our related construction (or design) picture.
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.