phonelogo+234 8146561114 or +2347015391124

DESIGN AND CONSTRUCTION OF A SMART INVERTER BATTERY CHARGER

USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a smart inverter battery charger". Please, sit back and study the below research material carefully. This project topic (design and construction of a smart inverter battery charger) have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a smart inverter battery charger" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a smart inverter battery charger" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.


TITLE PAGE

 

BY

---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

DECEMBER,2018



APPROVAL PAGE

This is to certify that the research work, "design and construction of a smart inverter battery charger" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator



DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.



ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.


PROJECT DESCRIPTION: This work "design and construction of a smart inverter battery charger" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and construction of a smart inverter battery charger" visible for everyone, then the complete material on "design and construction of a smart inverter battery charger" is to be ordered for. Happy viewing!!!


ABSTRACT

This project is on a Smart Inverter Battery Charger. The smart inverter battery charger circuit presented in this work will automatically charge a 12V  battery, or above. Special features of the charger are as follows. It automatically controls the charging current as per the status of the battery. Battery voltage level as well as charging status are indicated on the LCD display. The charger maintains float voltage, if battery is fully charged. Arduino identifies status of the battery connection and voltage, and indicates the same on the LCD.
TABLE OF CONTENTS

 TITLE PAGE

APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT

CHAPTER ONE

    1. INTRODUCTION
    2. BACKGROUND OF THE STUDY
    3. PROBLEM STATEMENT
    4. AIM/OBJECTIVES OF THE PROJECT
    5. SIGNIFICANCE OF THE PROJECT
    6. APPLICATION OF THE PROJECT
    7. LIMITATION OF THE PROJECT
    8. SCOPE OF THE PROJECT
    9. PROJECT WORK ORGANISATION
  1. CHAPTER TWO
  2. LITERATURE REVIEW
  3. 2.1      Review of Related works
  4. 2.2      Contribution to Knowledge
  5. 2.3      Proposed system’s Theories
  6. 2.4      Expected Results from Hardware &Software

CHAPTER THREE

3.0      CONSTRUCTION METHODOLOGY
3.1      BLOCK DIAGRAM OF THE SYSTEM

3.2      CIRCUIT DIAGRAM
3.3      CIRCUIT DESCRIPTION AND OPERATION
3.5      SOFTWARE USED

CHAPTER FOUR

RESULT ANALYSIS

4.1      CONSTRUCTION PROCEDURE AND TESTING
4.2      CASING AND PACKAGING
4.3      ASSEMBLING OF SECTIONS
4.4      TESTING OF SYSTEM OPERATIONOBSERVATIONS
4.6     PRECAUSION

CHAPTER FIVE

    1. SUMAMRY
    2. CONCLUSIONS/SUGGESTIONS

5.3     REFERENCES

CHAPTER ONE

1.0                                                     INTRODUCTION

    1. Background of the Study

A battery charger generally is described as is a device that provides electricity to convert into stored chemical energy for storage in an electrochemical cell by running an electric current through it. [Zhang et al, 2013].
A battery charger consists of a rectifier circuit, power circuit, ripple monitoring, control circuit, regulator circuit.
A Battery charger comes in various designs and voltage.  The choice of a particular charger depends largely on the size of battery. Mini battery charger could be used to charge batteries whose voltage is 12 volts. 
The battery charge is built in such a way that it delivers a constant value of d.c current into the battery it is charging in the opposite direction from which current flows on the batteries during discharge one cannot successfully design a battery charge without a fundamental understanding of the accumulator because it also makes up the operation according to [Zhang et al, 2013].
This work is aimed at building a digital battery charger which comprises of an arduino and LCD an the major component.

    1. Problem Statement

There is nothing that is so frustrating and dangerous as when a battery is plugged and at the end it was discovered that the battery did not charge. And nothing is as dangerous as when a battery was fully charged and the owner is not aware of the charging state. This study solve problems such as not knowing when a battery is charging and when it is fully charged which can cause the battery not to charged or to over-charge.
1.3                                        OBJECTIVES OF THE PROJECT
The main aim of the project is to build an arduino smart inverter battery charger. The objectives of the work are:

  1. To build the prototype of the device
  2. To automatically controls the charging current as per the status of the battery.
  3. To display the charging status of the charging battery on the LCD display.

1.4                                      SIGNIFICANCE OF THE PROJECT
Using this smart inverter battery charger will serve as a means of keeping a battery in good condition in that the charger maintains float voltage, if battery is fully charged. Arduino identifies status of the battery connection and voltage, and indicates the same on the LCD.
Apart from charging batteries, this device can also be used as a battery level monitor due to the battery level and digital display features.
Carrying this work will go along way teaching students how battery charger is been made and the operation of battery charger. This study will also be of great benefit to all users of charger and rechargeable devices in that it will help them to understand how their battery is been charged and how chargers are operated.

 

1.5                                       APPLICATION OF THE PROJECT
Smart inverter battery charger is used in the following devices for the purpose of recharging device batteries:

  1. It is used in inverter
  2. It is used in cellphone
  3. It is used in Solar energy system
  4. It is used in vehicles
  5. It is used in an uninterruptible power supply (UPS), etc.

1.6                                        LIMITATION OF THE PROJECT
The only problem with this device is that it takes longer time to recharge inverter battery because of the low current output, and it is design only for a 12 battery.

1.7                                              SCOPE OF THE PROJECT
The scope of this work covers building a smart inverter battery charger that is built around Arduino Uno (Board1), adjustable voltage regulator LM338 (IC1), 12V voltage regulator 7812 (IC2), 16×2 LCD (LCD1) and a few other components. The system automatically controls the charging current as per the status of the battery. Battery voltage level as well as charging status are indicated on the LCD display. The charger maintains float voltage, if battery is fully charged. Arduino identifies status of the battery connection and voltage, and indicates the same on the LCD.


CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and construction of a smart inverter battery charger" is also available. Order full work to download. Chapter two of "design and construction of a smart inverter battery charger" consists of the literature review. In this chapter all the related works on "design and construction of a smart inverter battery charger" were reviewed.

CHAPTER THREE: The complete chapter three of "design and construction of a smart inverter battery charger" is available. Order full work to download. Chapter three of "design and construction of a smart inverter battery charger" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of "design and construction of a smart inverter battery charger" is available. Order full work to download. Chapter four of "design and construction of a smart inverter battery charger" consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of "design and construction of a smart inverter battery charger" is available. Order full work to download. Chapter five of "design and construction of a smart inverter battery charger" consist of conclusion, recommendation and references.

 

CLICK HERE FOR MORE RELATED TOPICS/MATERIAL


To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions


For more information contact us through any of the following means:

Mobile No phonelogo:+2348146561114 or +2347015391124 [Mr. Innocent]

Email address emailus:engr4project@gmail.com

Watsapp No whatsapp.html :+2348146561114


COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp Nowhatsapp.html
:+2348146561114


E
mail Address emailus:engr4project@gmail.com


FOLLOW / VISIT US VIA:

tweeter instagram.htmlfacebook logomyyoutubelogo.html