This project is titled design and construction of a temperature control load. It is designed to control electric appliances such as electric kettle, oven, incubator, or lamp through the variation of temperature range (0°C -100°C) which must be set by the user or operator. And this can be achieved by the use of temperature sensor known as THERMISTOR. This thermistor is a temperature control device with a high or low resistance value which can go high or low when the temperature is increased or reduced depending on the type.
In this project, 100C is used as a set temperature. And this device is design in such a way that when the set temperature of the device is reached, the relay of the device will automatically triggered and will maintain this stage until when the temperature of the sensor is dropped 97°C, and then it will return normally open stage in order to maintain that 100°C. And this automatic feature is controlled by a high current relay.
TABLE OF CONTENT
Title Page
Approval Page
Dedication
Acknowledgement
Abstract
Table of Content
CHAPTER ONE
1.0 Introduction
1.1 objective of the project
1.2 significance of the project
1.3 application of the project
1.4 scope of the project
CHAPTER TWO
2.0 LITERATURE REVIEW
2.1 Overview of temperature controller
2.2 Review of different types of temperature controller and their working principle
2.3 Major Component’s Description
2.1 Resistors
2.2 Diodes
2.3 Capacitors
2.4 Transformers
2.5 Transistor
2.6 Integrated Circuit
2.7 Thermistor
CHAPTER THREE
3.0 Sectional Description of the System
3.1 Comparator Section
3.2 Switching (relay) Section
3.3 Power supply
3.4 sensor
3.5 circuit operation
CHAPTER FOUR
4.0 Construction Procedure and Testing
4.1 Casing and Packaging
4.2 Assembling of Sections
4.3 Testing of System Operation
4.4 Installation of the Completed System
4.5 Problem Encountered
4.6 Cost Analysis
CHAPTER FIVE
5.1 Conclusion
5.2 Recommendation
5.3 Bibliography
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE PROJECT
A temperature controlled automatic load controls appliances such as household electric kettle, which is usually has a heating element which is mounted at the bottom of a water tank through a heat conducting base. A conventional temperature control system typically uses a bi-metal temperature sensor (also known as a thermostat) to sense the temperature of the device, if it is used in electric kettle: the temperature of the water inside the kettle is measured and the steam when the water is boiled, and then cut off the electric power if the water temperature reaches the bi-metal action temperature point or if sufficient amount of steam is detected. Some modern temperature control switch uses more precise electronic temperature sensors such as the NTC (Negative Temperature Coefficient) resistors (thermistors), which are capable of sensing the temperature through a very wide range of points instead of just one point. In some cases, the control systems of the system is configured to take into account the temperature rising rate in addition to the absolute temperature value so that the control precision is greatly improved.
The idea behind the design and construction of this switch is to make available or alternative means providing safety and accuracy demand for switching household or industrial electrical appliances. This goes a long way in helping to curb the problem frequently encountered as a result of fire outbreak, burning of food, and inaccuracy found in measuring and maintaining temperature. That notwithstanding it makes it possible to have other means of heating food without constant temperature monitoring until when the required temperature will be achieved thereby creating time for the operator to be engaged on other works while the system is in operation.
Moreover, there are higher rate of fire accident cause by switching of devices. So there is every need that other means of safety should be made available for constant running of our electric equipments and gadgets and also to provide comfort to man. Hence, with the help of a Thermistor, which has come to solve the problem of fire accident and inaccuracy found in temperature measurement in Nigeria, a steady running and operation of our electric equipments and gadgets is guaranteed.
1.2 OBJECTIVE OF THE STUDY
The objective of this work is to design a device which will automatically control or switch ON and OFF electrical appliances by sensing the temperature of the environment or the device which it is controlling without the help of the user.
1.3 SIGNIFICANCE OF THE PROJECT
Temperature controlled load typically uses a temperature sensor (also known as a thermistor) to sense the temperature and then cut off the electric power if the temperature reaches the action temperature point. The temperature sensors, NTC (Negative Temperature Coefficient) resistors (thermistor), which is capable of sensing the water temperature through a very wide range of points.
1.4 APPLICATION OF THE PROJECT
Outside the culinary world, temperature control load is used for a number of purposes.
Furnace: A furnace can be used either to provide heat to a building or used to melt substances such as glass or metal for further processing. A blast furnace is a particular type of furnace generally associated with metal smelting (particularly steel manufacture) using refined coke or similar hot-burning substance as a fuel, with air pumped in under pressure to increase the temperature of the fire.
kiln: A kiln is a high-temperature temperature control electric kettles used in manufacturing to convert mineral feedstock (in the form of clay or calcium or aluminum rocks) into a glassier, more solid form. In the case of ceramic kilns, a shaped clay object is the final result, while cement kilns produce a substance called clinker that is crushed to make the final cement product.
Autoclave: An autoclave is an kettle-like device with features similar to a pressure cooker that allows the heating of aqueous solutions to higher temperatures than water's boiling point in order to sterilize the contents of the autoclave.
Industrial electric kettle:Industrial temperature control electric kettles are similar to their culinary equivalents and are used for a number of different applications that do not require the high temperatures of a kiln or furnace.
1.5 SCOPE OF THE PROJECT
Temperature controlled switch include a relay, power supply and a sensor for sensing the temperature of the environment or device, and a control unit being configured to collect data during the operation of the circuits. The control unit is also configured to execute a predetermined program and calculate a cut-off temperature based on the data and a predetermined target temperature. The control unit is further configured to turn off the electric power provided to the controlled appliances through a relay, when the temperature of the sensor is equal to or greater than the calculated cut-off temperature.
1.7 LIMITATION OF THE PROJECT
Though temperature controlled load is designed to controlled appliances, but when the sensor is directly exposed to liquid (water) can damaged the sensor thereby causing the sensor to malfunctioning.
This material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We make abstract and chapter one visible for everyone.
All Project Topics on this site have complete 5(five) Chapters . Each Project Material include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research for your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view more our related construction (or design) pics
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.