USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of a wireless lamp control using bluetooth" Please, sit back and study the below research material carefully. This project topic "design and construction of a wireless lamp control using bluetooth" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of a wireless lamp control using bluetooth " project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of a wireless lamp control using bluetooth" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

DESIGN AND CONSTRUCTION OF A WIRELESS LAMP CONTROL USING BLUETOOTH

BY

---
EE/H2013/01430
DEPARTMENT OF ---
SCHOOL OF --
INSTITUTE OF ---

DECEMBER,2018

---

APPROVAL PAGE

This is to certify that the research work, "design and construction of a wireless lamp control using bluetooth" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a B.Sc on --- has been approved.

By
Dr. ---                                                    Dr. ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
 Dr. ---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work “design and construction of a wireless lamp control using bluetooth” research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of “the rate and causes of infant mortality in edo state (case study of irrua specialist teaching hospital)” visible for everyone, then the complete material on “the rate and causes of infant mortality in edo state (case study of irrua specialist teaching hospital)” is to be ordered for. Happy viewing!!!

---

Wireless control system uses information technology to monitor and control ON and OFF of a lamp. The system is based on the embedded system and can act as a security guard to the home lamps.
The whole system is a cheaper one, but it provides the full-scale home device monitor and control function. By using the embedded system technique, it is convenient to use and allows simple installation in existing homes, it provide a safe, convenient home to us. The shortage of the system is only can turn on/off the electric lamps and the lack of the wireless function. With the Development of the smart electric lamps, the system must make much progress. 

TABLE OF CONTENTS

 TITLE PAGE

APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
TABLE OF CONTENT

CHAPTER ONE

• INTRODUCTION
• AIM/OBJECTIVE OF THE PROJECT
• SCOPE OF THE PROJECT
• OPERATING ENVIRONMENT
• LIMITATIONS OF THE PROJECT
• PROBLEMS AND ASSUMPTIONS OF THE PROJECT
• APPLICATIONS OF THE PROJECT
• SIGNIFICANCE OF THE PROJECT
• PROJECT WORK ORGANISATION

CHAPTER TWO

2.0      LITERATURE REVIEW
2.1      OVERVIEW OF THE PROJECT
2.2     HISTORICAL BACKGROUND OF THE PROJECT
2.3      REVIEW OF BLUETOOTH TECHNOLOGY
2.4      ORIGIN OF BLUETOOTH
2.5      ETYMOLOGY OF BLUETOOTH
2.6     IMPLEMENTATION OF BLUETOOTH
2.7     COMMUNICATION AND CONNECTION
2.8     USES OF BLUETOOTH

CHAPTER THREE
3.0       DESIGN METHODOLOGY
3.1      BASICS OF THE PROJECT
3.2     SYSTEM BLOCK DIAGRAM
3.3     DESCRIPTION OF SYSTEM BLOCK DIAGRAM
3.4    CIRCUIT DIAGRAM
3.5    COMPONENTS LIST
3.7    PROGRAM EXPLANATION
3.8    PROGRAME CODE
3.9    DESCRIPTION OF COMPONENTS USED
3.10  POWER SUPPLY UNIT

CHAPTER FOUR

4.0     RESULT ANALYSIS
4.1      CONSTRUCTION PROCEDURE AND TESTING ANALYSIS
4.2     CASING AND PACKAGING
4.3      ASSEMBLING OF SECTIONS
4.4    TESTING OF SYSTEM OPERATION
4.5     INSTALLATION OF THE COMPLETED DESIGN

CHAPTER FIVE

5.1      CONCLUSIONS
5.2      REFERENCES
CHAPTER ONE
1.0                                                        INTRODUCTION
1.1                                         BACKGROUND OF THE PROJECT
Initially communication was done by travelling from kilometre to kilometre to deliver messages but now the trend involves talking to people even when they are far away around the globe even to the extent of seeing them using the present day 3G technologies. Now mobile phones can be used to trigger their greatest revolution: by allowing us to run our homes lamps remotely. If you are heading home early on a sunny day to your house driving through traffic, your mobile phone can be used to switch ON your lamps at the touch of a keypad.
This paper presents design and construction of a wireless lamps controlling system using bluetooth. A cell (mobile) phone bluetooth acts as a modem for the control of electrical home lamps. This is achieved when the mobile phone number is dialed and an appropriate command button is pressed. The paper demonstrates how to develop a system that aids the control of remote devices using mobile phones to enable devices without infrared though connected to power sources to be controlled and considering the possibility of users to monitor the status and usage of these devices. It makes uses a AT89c51 microcontroller to control the switching of the output. This design is customized as a central device for four pieces of home lamps using relay to activate each of the respective lamps

1.2                                               PROBLEM STATEMENT
In the last decade, all electric lamps are manually operated, and this sometimes exposes the user to the risk of electric shock, and which also cause time wastage and also involves labour, but today the story has challenge which brought solutions to these problems by controlling home appliances wirelessly. Here, the project is based on remote control electric lamps, which could help to save energy like electricity and lots of physical strength. It could be secure, flexible, help to prevent power and more accurate outcomes.

1.3                                             OBJECTIVE OF THE PROJECT
The objective of this project is to enable users to remotely control their electric lamps using a cell phone bluetooth.  To access the control unit, the user should on their bluetooth with the required/desired function/action to his/her home control system via GSM.  Upon being properly authenticated, the cell phone-based interface at home (control unit) would relay the commands to a microcontroller that would perform the required function/action, and return a function completion bluetooth that would be sent to the source of the original command (user’s cell phone).

1.4                                                 SCOPE OF THE PROJECT
This device allows for a user to remotely control and monitor multiple electric lamps using a cellular phone. This system will be a powerful and flexible tool that will offer this service at any time, and from anywhere with the constraints of the technologies being applied. Possible target appliances include (but are not limited to) climate control systems, security systems, and lights; anything with an electrical interface.
The proposed approach for designing this system is to implement a microcontroller-based control module that receives its instructions and commands from a cellular phone bluetooth. The microcontroller then will carry out the issued commands and then communicate the status of a given appliance or device back to the cellular phone. For security purposes, a means of identification and user authentication will be implemented, and will combine caller identification with a password authorization.

1.5                                            OPERATING ENVIRONMENT

The control system will include two separate units: the cellular phone with bluetooth, and the control unit. There will therefore be two operating environments. The cellular phone will operate indoors and outdoors whereas the control unit will operate indoors within the temperature and humidity limits for proper operation of the hardware.

1.6                                          LIMITATIONS OF THE PROJECT

The following is a list of limitations for the project.
The device can only work when the user is within the Bluetooth coverage.
Only devices with electrical controlling input ports will be possible targets for control.
The receiver must have a power source (220vac) attached at all times.
Operation of the controlling unit is only possible through a cell phone with Bluetooth capabilities.
Bluetooth has a range of 10-15 meters, so this device can switch ON and OFF electric lamps within the range.

1.7                        PROBLEMS AND ASSUMPTIONS OF THE PROJECT

The following is a list of problems and assumptions for the project;
The user and control unit will establish communication via bluetooth.
The controlled appliances will have to have an electrical interface in order to be controlled by microcontroller.

1.8                                         APPLICATIONS OF THE PROJECT

This project can be used in Industries, This system can be employed in houses, where people often forget to switch off their lamps. This work is aimed toward average consumers who wish to control ac lamps remotely from their cell phones provided that the appliances are electrically controllable.  It can prove very useful for disabled people. This project can also be used in shop, offices, industry.

1.9                                         SIGNIFICANCE OF THE PROJECT
electric lamps Controlling system using bluetooth can be used to turn on / off of electric lamps in our home. Then user has to press various keys to control the devices. In this work:

• Quick response is achieved.
• Construction is easy.
• Easy to maintain and repair.
• Comparatively the operation cost is less.
• Design is efficient and low cost.
• Power consumption is low.
• Controlling electrical devices wirelessly
• Saves electricity (when we forget to switch off and go out).
• We can control appliances from any place round the globe.
• No coding is required.

1.10                                                     METHODOLOGY
To achieve the aim and objectives of this work, the following are the steps involved:

• Study of the previous work on the project so as to improve it efficiency.
• Draw a block diagram.
• Test for continuity of components and devices,
• Design of was carried out.
• Studying of various component used in circuit.
• Construct the circuit.
• Finally, the whole device was cased and final test was carried out.

1.10                                      PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to this study. In this chapter, the background, significance, objective limitation and problem of this study were discussed.
Chapter two is on literature review of this study. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.

CHAPTER TWO: The complete chapter two of “design and construction of a wireless lamp control using bluetooth” is available. Order full work to download. Chapter two of “design and construction of a wireless lamp control using bluetooth” consists of the literature review. In this chapter all the related work on “design and construction of a wireless lamp control using bluetooth"

CHAPTER THREE: The complete chapter three of “design and construction of a wireless lamp control using bluetooth” is available. Order full work to download. Chapter three of “design and construction of a wireless lamp control using bluetooth” consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of "design and construction of a wireless lamp control using bluetooth” is available. Order full work to download. Chapter four of “design and construction of a wireless lamp control using bluetooth” consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of design and construction of a “design and construction of a wireless lamp control using bluetooth” is available. Order full work to download. Chapter five of “design and construction of a wireless lamp control using bluetooth” consist of conclusion, recommendation and references.

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

You can also visit our facebook Page at fb.me/hyclas to view our related construction (or design) picture.

---

For more information contact us through Any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com

---

IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.