DESIGN AND CONSTRUCTION OF AN AUTOMATIC EMERGENCY LIGHTING SYSTEM
USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of an automatic emergency lighting system" Please, sit back and study the below research material carefully. This project topic "design and construction of an automatic emergency lighting system" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of an automatic emergency lighting system" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of an automatic emergency lighting system" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
DESIGN AND CONSTRUCTION OF AN AUTOMATIC EMERGENCY LIGHTING SYSTEM
BY
---
EE/H2013/01430
DEPARTMENT OF ---
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work, "design and construction of an automatic emergency lighting system" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on Electrical and Electronics Engineering has been approved.
By
Dr. --- Dr. ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
Dr. ---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work “design and construction of an automatic emergency lighting system” research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of “design and construction of an automatic emergency lighting system” visible for everyone, then the complete material on “design and construction of an automatic emergency lighting system” is to be ordered for. Happy viewing!!!
An emergency light is a lighting device that switches on automatically when a building experiences a power outage. Emergency lights are used in commercial and high occupancy residential buildings, such as college dormitories. Most building codes require that they be installed in older buildings as well. It is powered by a 3v NiCad battery that is being charged by the main power line when there is no blackout.
TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRCT
TABLE OF CONTENT
CHAPTER ONE
- INTRODUCTION
- BACKGROUND OF THE PROJECT
- AIM/OBJECTIVE OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- SCOPE OF THE PROJECT
- LIMITATION OF THE PROJECT
- APPLICATION OF THE PROJECT
- ADVANTAGES OF THE PROJECT
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
2.0 LITERATURE REVIEW
2.1 HISTORICAL BACKGROUND OF THE PROJECT
2.2 MODERN INSTALLATIONS OF THE PROJECT
2.3 DESCRIPTION OF POWER OUTAGE
2.4 TYPES OF POWER OUTAGE
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY
3.1 BLOCK DIAGRAM OF THE SYSTEM
3.2 CIRCUIT DIAGRAM
3.3 CIRCUIT DESCRIPTION
3.4 SYSTEM OPERATION
3.6 COMPONENTS LIST
3.7 DESCRIPTION OF MAJOR COMPONENTS USED
CHAPTER FOUR
4.0 RESULT ANALYSIS
4.1 CONSTRUCTION PROCEDURE AND TESTING
4.2 ASSEMBLING OF SECTIONS
4.3 CONSRUCTION OF THE CASING
4.4 TESTING
4.5 INSTALLATION OF THE COMPLETED DESIGN
CHAPTER FIVE
- CONCLUSIONS
- RECOMMENDATION
5.3 REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
1.1 BACKGROUND OF THE STUDY
In modern society, it is impossible to imagine life without electricity. Modern lives require a continuous supply of electricity. Not only industry, but also in the household. Take the case of an ordinary refrigerator. If you experience a power off situation, your food will be spoilt. But much more important, what if the power failure "spoils" your business. For example, uninterrupted power supply is needed for your server, which manages your accounting programme or provides uninterrupted operation of your website.
Emergency lights are very useful electrical gadgets and are quite popular, too. During a power failure these portable lights are able to instantly illuminate through battery backup and never allow us to stumble in the darkness. Although you will find a variety of them in different shapes and sizes in the market, but building your own emergency light at home can be a totally different experience. It will not only help you to create a quality design but also will acquaint you to the technical aspects of the unit. Besides, you also get an opportunity to customize the circuit as per your own needs.
The idea of the present emergency light circuit is truly compact, highly advanced, and may be kept plugged into the mains socket for a permanent automatic operation. The use of a Li-Ion battery makes it infinitely long lasting.
1.2 PROBLEM STATEMENT
Power failure causes total darkness during night or dark hours which cause occupants of the house hitting or dashing their leg or feet against house properties such as center table which can cause serious injury to the occupant. Emergency lighting system came to solve this problem - it automatically illuminates the house when power outage occurs.
1.3 OBJECTIVE OF THE PROJECT
The objective of the work is to construct a device that When a power outage occurs, the lamp automatically illuminates. Instead of illuminating a lamp, when power supply is restored, the lamp is switched-off.
1.4 SIGNIFICANCE OF THE PROJECT
This device Provides light when the ordinary lighting fails due to a power cut. Required especially in villages where there are long power cuts. It is important to install it near stairs or the place where level changes. Near safety signs it should be installed.
Basically a battery packed light device. This automatically switched on when the light is switched off or there is a blackout. It is common in commercial and standard residential buildings. This device is:
- Battery Efficient
- Pollution free.
- Easy to use.
- Very cheap
- Easy to install anywhere.
1.5 SCOPE OF THE PROJECT
Automatic Emergency light is often considered same as a light device running on an inverter. It is considered a device which has its one end connected to a power source and when the power supply is cut, the bulb glows with the power of inverter. emergency lighting work on the principle that when a power failure occurs in a household at night, a power failure light responds to provide emergency illumination so that the occupants may move about safely in order to take measures to restore the illumination either by changing fuses, if necessary, or by finding and deploying other light sources such as candles, portable electric lanterns, or the like.
1.6 LIMITATION OF THE PROJECT
- Not Durable
- A bit delicate circuit
1.7 ADVANTAGES OF THE PROJECT
- This is very simple circuit and the cost is also very less.
- power is saved because the circuit switches the LEDs based on light conditions
1.8 APPLICATIONS OF THE PROJECT
- Used in child’s study rooms to avoid the sudden power failure.
- As an emergency lamp in homes.
- Used in security systems to switch ON the lights automatically during the power failure.
1.9 PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to an automatic emergency lighting system. In this chapter, the background, significance, objective limitation and problem of an automatic emergency lighting system were discussed.
Chapter two is on literature review of an automatic emergency lighting system. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
CHAPTER TWO: The complete chapter two of “design and construction of an automatic emergency lighting system” is available. Order full work to download. Chapter two of “design and construction of an automatic emergency lighting system” consists of the literature review. In this chapter all the related work on “design and construction of an automatic emergency lighting system” was reviewed.
CHAPTER THREE: The complete chapter three of “design and construction of an automatic emergency lighting system” is available. Order full work to download. Chapter three of “design and construction of an automatic emergency lighting system” consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of “design and construction of an automatic emergency lighting system” is available. Order full work to download. Chapter four of “design and construction of an automatic emergency lighting system” consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of “design and construction of an automatic emergency lighting system” is available. Order full work to download. Chapter five of “design and construction of an automatic emergency lighting system” consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view our related construction (or design) picture.
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.