USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p". Please, sit back and study the below research material carefully. This project topic ( design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p) have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their s[tudents to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

DESIGN AND CONSTRUCTION OF AN AUTOMATIC SOLAR WATER PUMP CONTROLLER USING ULTRASONIC SENSOR AND ATMEGA328P

BY

---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

DECEMBER,2018

---

APPROVAL PAGE

This is to certify that the research work, " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" visible for everyone, then the complete material on " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" is to be ordered for. Happy viewing!!!

---

This project is titled the design and construction of an automatic solar water level controller system.
The project is designed to give a display of water level in a tank and control a pump motor as required. The reading given is in the scale of 0 to 9. A priority encoder is interfaced to a decoder to get the display of water level on 7 segment display. This is the circuit designed for overhead tank digital water level indicator. It is built around priority encoder, BCD-to-7-segment decoder, 7-segment display and a few discrete components. Due to high input impedance, priority encoder senses water in the container from its nine input terminals. In this Arduino based automatic water level indicator and controller project we are going to measure the water level by using ultrasonic sensors. Basic principal of ultrasonic distance measurement is based on ECHO. When sound waves are transmitted in environment then they return back to the origin as ECHO after striking on any obstacle. So we have to only calculate its traveling time of both sounds means outgoing time and returning time to origin after striking on any obstacle. And after some calculation we can get a result that is the distance. This concept is used in our water controller project where the water dc motor pump is automatically turned on when water level in the tank becomes low.

TABLE OF CONTENT
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT
CHAPTER ONE

1. INTRODUCTION
1. BACKGROUND OF THE PROJECT
2. PURPOSE OF THE PROJECT
3. AIM OF THE PROJECT
4. OBJECTIVE OF THE PROJECT
5. SIGNIFICANCE OF THE PROJECT
6. SCOPE OF THE PROJECT
7. APPLICATION OF THE PROJECT
8. LIMITATION OF THE PROJECT
9. PROJECT JUSTIFICATION
10. PROJECT ORGANIZATION

CHAPTER TWO
2.0     LITERATURE REVIEW
2.1     REVIEW OF DIFFERENT TYPE OF WATER CONTROLLER
2.2      REVIEW OF DIFFERENT TYPES OF WATER SENSOR
2.3      THE CONCEPT OF WATER LEVEL CONTROLLER SYSTEM
CHAPTER THREE
3.0     CONSTRUCTIONS METHODOLOGY
3.1     CIRCUIT DIAGRAM
3.2     CIRCUIT DESCRIPTION
3.3     CIRCUIT OPERATION OF THE WATER INDICATOR
3.4     COMPONENTS USED
3.5     THE WORKING PRINCIPLE
3.5     POWER SUPPLY UNIT
3.6     SPECIFICATION AND OPERATION OF SYSTEM COMPONENT
3.7     MICROPROCESSOR UNIT
CHAPTER FOUR
4.0     RESULT ANALYSIS
4.1     INSTALLATION OF THE COMPLETE DESIGN
4.2     CONSTRUCTION PROCEDURE AND TESTING
4.3     CASING AND PACKAGING
4.4     ASSEMBLING OF SECTION
4.4     TESTING OF SYSTEM OPERATION
4.5     PROBLEMS ENCOUNTERED
4.6     COST ANALYSIS
4.7     DESCRIPTION OF COMPONENTS USED
CHAPTER FIVE
5.1     CONCLUSION
5.2     RECOMMENDATION
5.3     BIBLIOGRAPHY

CHAPTER ONE
1.0                                                        INTRODUCTION
This work is on an automatic solar water pump which is an Electronic Equipment which when electrically connected to the starter of any given dc pump -set motor will control the operation of the pump- set depending upon the water level in the Source and Destination Storage Tanks through a renewable energy source (solar energy). It Switches ON the Pump-set when Water level drops below pre-set level in Overhead Tank, Switches OFF the Pump-set when Water level in Overhead Tank becomes full ,Switches OFF the Pump-set when Water level is low in tank , and Switches ON the Pump-set when there is sufficient water in the tank.
The idea can be implicitly used to ascertain and control the level of water in overhead tanks and prevent wastage. In this Arduino based automatic water level indicator and controller project the water level is being measured by using ultrasonic sensors.Working of IC is very simple. Initially consider that tank is empty, when power supply is on all the input of IC1 is high. From truth table of IC1 you can see that is if input is high then it will give you high on output pin also. This will make the input pin of IC2 low and 0 is displayed on seven segment display. Now when water in tank reaches level 1 than it will make the pin 11 of IC1 low and remaining pin remain pin high as a result we will get a output from pin 9 of IC1. Similarly when level in the tank reaches to level 2 it will make pin 12 of IC1 low and 11 is already low but 74147 is a priority encoder that's why output from pin 7 is received and again this low signals are converted into high output with the help of transistor T3 and we will get  numeric 2 display son 7 segment display. This indicates that water has reached to level 2. When sound waves are transmitted in environment then they return back to the origin as ECHO after striking on any obstacle. So its traveling time of both sounds means outgoing time and returning time to origin after striking on any obstacle is being calculated. And after some calculation a result is obtained that is the distance. This concept is used in our water controller project where the water motor pump is automatically turned on when water level in the tank becomes low. As water in tank fills we will get numeric 3, 4 9 to be display. The circuit automatically switches the motor OFF when the tank is full. The water level is displayed on a 7 segment display.

1.1                                                 AIM OF THE PROJECT
The aim of this work is to construct a solar device used to pump, measure and display the level of water in a container and avoid overflow of water. The function of the solar panel is produce a constant power supply to the controller and the dc water pump.

1.2                                             OBJECTIVE OF THE PROJECT
The objective of this project is to notify the user the amount of water that is present in the overhead water tank. This project can be further determine enhanced to control the water level in the tank by turning it ON, when the water level is LOW, and turning it OFF when the water level is HIGH. Thus, the Arduino water level indicator helps in preventing wastage of water in overhead tank. This project is wireless so, it is easy to install and it can work up to 100 meters.
1.3                                         SIGNIFICANCE OF THE PROJECT

An Automatic Water Level Controller (AWLC) will automatically START the pump set as soon as the water level falls below the predetermined level (usually kept half or 2/3rd tank) and shall SWITCH OFF the pump set as soon as tank is full or water level in the lower tank is at below minimum level.

This system provides you the flexibility to decide for yourself the water levels for operations of pump set in upper/lower tanks.

Built in Indications for showing Full, Empty Levels in Upper Tank and Lower Tank Empty Indication.

c. Manual operation switch for special operations like watering the plants from pump set.

The system ensures no overflows or dry running of pump there by saves electricity and water.

Consume very little energy, ideal for continuous operation.

Suitability: These water level controllers are ideally suited for normal water as well as for ultra low conductivity water with less than 1 micro/moh. Easy to Operate: this system come fitted with sensitivity setting which can be provided externally on a dial or with internal settings. Settings: It is equipped with technology which works on low or high sensitivity settings on the same machine and thereby saves costs of buying and using two different machines. Materials of Construction: this water control system is protected the against corrosion. Safety: This system is highly insulated, leakage proof and works without creating any noise.  Save roofs Save water

1.4                                       APPLICATION OF THE PROJECT
Water level controller is an application which detects the level water then triggers the pump and vice versa. They are useful devices and play an important role in various industries such as automobile, irrigation, and also at homes, or wherever water is pump either underground or overhead.
1.5                                              SCOPE OF THE PROJECT

This solar water pump controller will give you a heads-up the instant over-head tank and underground tank is full or goes below the required level, hopefully giving you time to close windows and bring in possessions. In this work, an Ultrasonic sensor is used in the transmitter circuit, which measures the distance of water level from the upper point of the bottle or Tank. The distance is measured in centimeters and sent to receiver circuit using RF communication. The water level is shown in terms of percentage on a 16×2 LCD module, which is connected to receiver circuit.

---

CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" is also available. Order full work to download. Chapter two of " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" consists of the literature review. In this chapter all the related work on " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" was reviewed.

CHAPTER THREE: The complete chapter three of " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" is available. Order full work to download. Chapter three of " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" is available. Order full work to download. Chapter four of " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of design and construction of a " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" is available. Order full work to download. Chapter five of " design and construction of an automatic solar water pump controller using ultrasonic sensor and atmega328p" consist of conclusion, recommendation and references.

 

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

---

For more information contact us through any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp No :+2348146561114

Email Address :engr4project@gmail.com

---

FOLLOW / VISIT US VIA: