DESIGN AND CONSTRUCTION OF AN SMPS BASED 12V AUTOMATIC BATTERY CHARGER WITH BATTERY FULL CUT-OFF AND DIGITAL DISPLAY
USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display". Please, sit back and study the below research material carefully. This project topic "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
BY
---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work, "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.
By
--- . ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" visible for everyone, then the complete material on "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" is to be ordered for. Happy viewing!!!
This project is on a SMPS based 12v automatic battery charger with battery full cut-off and digital display. The Automatic Battery Charger circuit presented in this work can automatically charge a 12V battery. Special features of the charger are as follows. It automatically controls the charging current as per the status of the battery. Battery voltage level as well as charging status are indicated on the LCD display. At end of this work a switching power supplies was built which have high efficiency and durable which is fit to be used in a variety of electronic equipment, including computers and other sensitive equipment requiring stable and efficient power supply.
TABLE OF CONTENTS
Title page
Approval page
Dedication
Acknowledgement
Abstract
Table of content
CHAPTER ONE
- Introduction
- Background of the study
- Problem statement
- Aim/objectives of the project
- Significance of the project
- Application of the project
- Scope of the project
- Project work organisation
CHAPTER TWO
LITERATURE REVIEW
2.1 Review of Related works
2.2 Switch mode power supply
2.3 Types of switch mode power supply
2.4 Application of switch mode power supply
2.5 Advantages and disadvantages of switch mode power supply
2.6 Contribution to Knowledge
2.7 Proposed system’s Theories
CHAPTER THREE
3.0 METHODOLOGY3.1 Block diagram of the system
3.2 Circuit Diagram
3.3 Circuit description and operation
CHAPTER FOUR
RESULT ANALYSIS
4.1 Construction procedure and testing
4.2 Casing and packaging
4.3 Assembling of sections
4.4 Testing of system operation
4.6 Precaution
CHAPTER FIVE
- Conclusions
- Recommendation
5.3 REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
1.1 Background of the Study
A battery charger is described as is a device that provides electricity to convert into stored chemical energy for storage in an electrochemical cell by running an electric current through it (Zhang et al, 2013).
A battery charger that is based on switched-mode power supply (SMPS) is an electronic circuit that converts power using switching devices that are turned on and off at high frequencies, and storage components such as inductors or capacitors to supply power when the switching device is in its non-conduction state. The circuit was built around TNY267 switching regulator which performs the functions of the PWM generator, MOSFET chopper switch, error amp, and control circuit.
A Battery charger comes in various designs and voltage. The choice of a particular charger depends largely on the size of battery. Mini battery charger could be used to charge batteries whose voltage is 12 volts.
It converts an AC power line voltage to a steady state DC output voltage as required by all electronic circuits. The SMPS circuit of the charger converts the available unregulated AC or DC input to a regulated DC output. The input is taken from the AC mains and then rectified, filtered and fed to a high frequency DC-DC converter. SMPS circuit of the charger can be operated within the kHz to MHz frequency range. The increased switching frequencies cause a decrease in the size of the energy storage elements, such as the capacitors, inductors and transformers, in an almost linear manner [3]. The battery charge is built in such a way that it delivers a constant value of d.c current into the battery it is charging in the opposite direction from which current flows on the batteries during discharge one cannot successfully design a battery charge without a fundamental understanding of the accumulator because it also makes up the operation according to [Zhang et al, 2013].
This work is aimed at building a SMPS based digital battery charger with battery full cut off feature and LCD.
1.2 PROBLEM STATEMENT
Using switch Mode power supply in a battery charger was invented to solve problems observed in conventional battery charger such as low frequency and efficiency. Linear DC regulated power supplies (“linear supplies”) used in switch Mode power supply alters the output voltage to the required value through the power frequency (50/60 Hz alternating current) voltage transformer [8]. After being lowered (or raised) to the appropriate AC voltage value, the waveform is rectified, filtered, and stabilized by a voltage regulation circuit, and is then output as a regulated direct current (DC) which can be used to charge a 12v battery charger.
1.3 AIM AND OBJECTIVES OF THE PROJECT
The main aim of the project is to build an SMPS based 12v automatic battery charger with battery full cut-off and digital display. The objectives of the work are:
- To build the prototype of the device
- To automatically controls the charging current as per the status of the battery.
- To display the charging status of the charging battery on the LCD display.
- To increase frequency and efficiency of a battery charger.
1.4 SIGNIFICANCE OF THE PROJECT
Using this digital display charger will serve as a means of keeping a battery in good condition in that the charger maintains float voltage, if battery is fully charged.
Apart from charging batteries, this device can also be used as a battery level monitor due to the battery level and digital display features.
Carrying this work will go a long way teaching students how SMPS based battery charger is been made and the operation of battery charger. This study will also be of great benefit to all users of charger and rechargeable devices in that it will help them to understand how their battery is been charged and how chargers are operated.
In a switching power supply, the regulating device operates in the saturation or cut-off area as opposed to the linear power supply regulator which operates in the less efficient linear range.
Switching power supply has Small size, lighter weight, and higher efficiency (can reach nearly 99%). It also have larger output ripple, RFI/EMI interference from pulsed power, higher output voltage if failure occurs [14].
1.5 APPLICATION OF THE PROJECT
Battery charger is used in the following devices for the purpose of recharging device batteries:
- It is used in inverter
- It is used in cellphone
- It is used in Solar energy system
- It is used in vehicles
- It is used in an uninterruptible power supply(UPS), etc.
1.7 SCOPE OF THE PROJECT
The scope of this work covers building an SMPS based digital battery charger which incorporates a switching regulator to convert electrical power efficiently. It is mainly used for obtaining a controlled dc power supply as output. It is used to convert power (voltage) using switching devices that are turned on and off alternatively at high frequencies. It uses storage components like inductors or capacitors to supply power when the switching device is in its non-conduction state (off-state). SMPS circuit possesses high efficiency and is widely used in various electronic equipment such as computers, battery chargers, and other sensitive equipment requiring a stable and efficient power supply.
The system automatically controls the charging current as per the status of the battery. Battery voltage level as well as charging status is indicated on the LCD.
1.8 PROJECT WORK ORGANISATION
CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" is also available. Order full work to download. Chapter two of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" consists of the literature review. In this chapter all the related work on "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" was reviewed.
CHAPTER THREE: The complete chapter three of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" is available. Order full work to download. Chapter three of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" is available. Order full work to download. Chapter four of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" is available. Order full work to download. Chapter five of "design and construction of an smps based 12v automatic battery charger with battery full cut-off and digital display" consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
For more information contact us through any of the following means:
Mobile No 
:+2348146561114 or +2347015391124 [Mr. Innocent]
Email address 
:engr4project@gmail.com
Watsapp No 
:+2348146561114
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
FOLLOW / VISIT US VIA:
