DESIGN AND CONSTRUCTION OF HEADPHONE AMPLIFIER
Headphone amplifier drives headphones instead of loudspeakers. Most commonly they are found embedded in electronic devices such as integrated amplifiers, portable music players and televisions, but standalone units are not uncommon.
Headphone amplifier can provide the voltage levels necessary to drive the headphones. Most headphone amplifiers provide power between 10 mW and 2 W depending on the specific headphone being used and the design of the amplifier. Certain high power designs can provide up to 6W of power into low impedance loads, although the benefit of such power output with headphones is unclear, as the few headphones that have sufficiently low sensitivities to function with such power levels will reach dangerously high volume levels with such amplifiers.
CHAPTER ONE
1.1 INTRODUCTION
A headphone amplifier is a low-powered audio amplifier designed particularly to drive headphones worn on or in the ears, instead of loudspeakers in speaker enclosures. Most commonly, headphone amplifiers are found embedded in electronic devices that have a headphone jack, such as integrated amplifiers, portable music players (e.g., iPods), and televisions.
Effectively, a headphone amplifier is a small power amplifier that can be connected to a standard headphone jack or the line output of an audio source. Electrically, a headphone amplifier can be thought of as an amplifier that presents a very high input impedance and presents a lower output impedance and larger range of output voltages. This allows headphones of a low sensitivity to be driven louder as a result of the extra voltage provided by the amplifier. There is potential fidelity gains if headphones are driven with lower distortion than using a headphone amplifier integrated into a general purpose audio product. In practice, this most often occurs when using low impedance headphones with consumer electronics with insufficiently low output impedance.
1.2 OBJECTIVE OF THE PROJECT
The objective is to design a benchmark performance and low cost amplifier used in powering headphone. Headphone amplifiers are found embedded in electronic devices that have a headphone jack, such as integrated amplifiers, portable music players, and televisions.
1.3 SIGNIFICANCE OF THE PROJECT
Just like a good room speaker can improve when partnered with a great power amp, a headphone is a miniature speaker system that can benefit from a headphone amp to sound its best.
With headphones, an uncompressed music source and a great headphone amp, you'll be astonished at the level of pure clarity, huge dynamic range and deep musical detail you'll be able to hear.
Big speaker systems may out-perform headphones in terms of visceral sonic impact; great headphones can deliver much superior audio resolution and access to nuanced low-level information obscured in the recording.
1.4 APPLICATION OF THE PROJECT
This device is found embedded in electronic devices such as integrated amplifiers, portable music players and televisions, for the listen pleasure of the user.
1.5 SCOPE OF THE PROJECT
This headphone amplifier circuit design is normally used to drive a headphone with relative low impedance. It provides one watt power output and it can also be applied as an output stage for preamplifiers in conjunction with active loudspeakers boxes. The headphone amp is composed of an OP-AMP and an additional transistor amplifier. Input signals pass through a low pass filter composed of resistor and capacitor. Its amplification together with a relatively “fast” OPAMP provides a low distortion factor.
1.6 PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to a headphone amplifier. In this chapter, the background, significance, objective limitation and problem of a headphone amplifier were discussed.
Chapter two is on literature review of a headphone amplifier. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
This material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We make abstract and chapter one visible for everyone.
All Project Topics on this site have complete 5(five) Chapters . Each Project Material include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research for your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.