USER'S INSTRUCTIONS: The project work you are about to view is on "design and construction of rf based remote controller for electric lamp". Please, sit back and study the below research material carefully. This project topic (design and construction of rf based remote controller for electric lamp) have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and construction of rf based remote controller for electric lamp" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and construction of rf based remote controller for electric lamp" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

 

BY

---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

DECEMBER,2018

---

APPROVAL PAGE

This is to certify that the research work, "design and construction of rf based remote controller for electric lamp" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work "design and construction of rf based remote controller for electric lamp" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and construction of rf based remote controller for electric lamp" visible for everyone, then the complete material on "design and construction of rf based remote controller for electric lamp" is to be ordered for. Happy viewing!!!

---

This project work deals on the design and construction of an Rf based remote control for an electronic/electrical device say electric lamp with the aim of switching on/off of the lamp at discretion and from a distance. It also eliminates the inconveniences associated with manual switching of lamps.  This electronic system is designed in two functional units; the transmitter and the receiver using radio frequency (RF) communication wave band.  The transmitter is a hand-held remote control while the receiver consists of a tuned radio frequency receiver, clock generator, delay circuit, flip-flop and a driver circuitry and electromagnetic relay which actuates the load (lamp).  When the remote control button is pressed, the lamp comes ON and remains ON until the remote is pressed again – it goes OFF.  Many advantages are accredited to this design in terms of robust, durability, cost effectiveness and components availability.  The result being the simple design of a system easy to operate and maintain. A miniaturized design of it will be a reliable, robust and rugged consumer electronics that will sell like a German burger.

TABLE OF CONTENTS
COVER PAGE
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
CHAPTER ONE
1.1   INTRODUCTION
1.2   BACKGROUND OF THE PROJECT
1.3   GENERAL DESCRIPTION OF THE PROJECT
1.4   OBJECTIVES OF THE PROJECT
1.5   AIM OF THE PROJECT
1.6   SIGNIFICANCE OF THE PROJECT
1.7   APPLICATION OF THE PROJECT
1.8   PROBLEM OF THE PROJECT
1.9   SCOPE OF THE PROJECT
1.10  PROJECT REPORT ORGANIZATION

CHAPTER TWO
LITERATURE REVIEW

• REMOTE CONTROL TECHNOLOGY
• INFRARED, LINE OF SIGHT AND OPERATING ANGLE

2.3     REMOTE CONTROL TECHNOLOGIES
CHAPTER THREE
3.0     METHODOLOGY
3.1      CIRCUIT DIAGRAM
3.2       TRANSMITTER SECTION
3.3     RECEIVER SECTION
3.4      COMPONENT DESCRIPTION

CHAPTER FOUR
4.1      RESULT ANALYSIS
4.2      CONSTRUCTION PROCEDURE AND TESTING ANALYSIS
4.3      CASING AND PACKAGING
4.4       INSTALLATION OF THE COMPLETED DESIGN
4.5       TESTING
4.6       ECONOMIC OF THE PROJECT
4.7      PROJECT EVALUATION
CHAPTER FIVE

• CONCLUSION
• RECOMMENDATION
• REFERENCES

 

 

 

CHAPTER ONE
1.1                                                         INTRODUCTION
Electronic communication has gained a holistic approach in the world technological growth.  Apparently, no modern electronic system is capable of fascinating the society without an aspect of telecommunication. This trend is so progressive that most remote control systems are designed with RF.
1.2                              GENERAL DESCRIPTION OF THE PROJECT
The above-mentioned development motivated me to embark on a project research work on the design and construction of an Rf based remote control electric lamp.  This electronic system is designed with a handheld remote control realized using frequency generator and modulator coupled into a tuned class-C amplifier.  The amplified signal is radiated into the atmosphere through a tank circuit at a particular frequency. The receiver is realized with a tuned radio frequency (TRF) receiver coupled into a transistor static switch.  These solid state switches are used to clock a D-type flip-flop through a delay circuit. The output of the flip-flop biases a driver circuitry realized using a Darlington pair transistors which drives the relay to switch ON/OFF the lamp connected to its normally open contact, whenever the remote is pressed.
1.3                                   OBJECTIVES OF THE STUDY/PROJECT
One of the objectives of this project is to design and implement an Rf based remote control for electric lamp capable of switching ON/OFF of electric lamp from a maximum distance of 200m at convenience.
It is also aimed at exposing the graduating student to electronic system design using random logic. It is also aimed at familiarizing the young engineers with digital system design involving telecommunication systems.  Another objective of this project is to ground the young engineers in engineering design which is indispensable in engineering professional practice.
1.4                                  SIGNIFICANCE OF THE PROJECT
This project work signifies a lot in telecom, computer and electronic engineering. It is very useful in a number of domestic places like in bedroom and security lamps in the compound. A project of this type if modified can be used as a gate/door opening system, car immobilizer and for industrial process control.  Another vital significance of this system is in the control of Air conditioner and refrigerators and other lamps in modern buildings. This system can be used to start and stop a power generating set from a distance.
1.5                                            SCOPE OF THE PROJECT
This project work covers the following: tuned radio frequency transmitter and receiver, flip-flops, Darlington pair transistors and delay circuits.  It also lays great emphasis on passive and active components used to implement the system. It x-rays the mode of calculation of the basic circuit parameters and other areas of application of the system.
1.6                                          APPLICATION OF THE PROJECT
This device can be used to control the power supply of appliances such as:

• TV
• DVD
• Radio etc.

1.7                                           LIMITATION OF THE PROJECT
To operate this device becomes a problem when the remote is fault or whenever the battery of the remote runs down
1.8                       PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to this study. In this chapter, the background, significance, objective limitation and problem of this study were discussed.
Chapter two is on literature review of the study. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.

---

CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and construction of rf based remote controller for electric lamp" is also available. Order full work to download. Chapter two of "design and construction of rf based remote controller for electric lamp" consists of the literature review. In this chapter all the related works on "design and construction of rf based remote controller for electric lamp" were reviewed.

CHAPTER THREE: The complete chapter three of "design and construction of rf based remote controller for electric lamp" is available. Order full work to download. Chapter three of "design and construction of rf based remote controller for electric lamp" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of "design and construction of rf based remote controller for electric lamp" is available. Order full work to download. Chapter four of "design and construction of rf based remote controller for electric lamp" consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of "design and construction of rf based remote controller for electric lamp" is available. Order full work to download. Chapter five of "design and construction of rf based remote controller for electric lamp" consist of conclusion, recommendation and references.

 

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

---

For more information contact us through any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp No :+2348146561114

Email Address :engr4project@gmail.com

---

FOLLOW / VISIT US VIA: