USER'S INSTRUCTIONS: The project work you are about to view is on "design and fabrication of a motorized chain hacksaw with infrered sensor". Please, sit back and study the below research material carefully. This project topic "design and fabrication of a motorized chain hacksaw with infrered sensor" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and fabrication of a motorized chain hacksaw with infrered sensor" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and fabrication of a motorized chain hacksaw with infrered sensor" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

 

BY

---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

---

APPROVAL PAGE

This is to certify that the research work, "design and fabrication of a motorized chain hacksaw with infrered sensor" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work "design and fabrication of a motorized chain hacksaw with infrered sensor" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and fabrication of a motorized chain hacksaw with infrered sensor" visible for everyone, then the complete material on "design and fabrication of a motorized chain hacksaw with infrered sensor" is to be ordered for. Happy viewing!!!

---

The objective of this work is to automate the conventional power hacksaw machine in order to achieve high productivity of work-pieces than the power hacksaw machine using Microcontroller. The automated machine acquires two inputs from the user namely the number of pieces to be cut and the length of each piece that is required to be cut. The inputs are given by the user with the help of a keypad and an LCD display, which will help the user to verify the data given by him. The operator need not measure the length of the work-piece that is to be cut and to load and unload the work-piece from the chuck each time after a piece has been cut. After acquiring the two inputs from the user, the machine automatically feeds the given length of work-piece in to a chuck and starts to cut till the given number of work-pieces has been cut. The machine feeds the work-piece with the help of a conveyor, which is driven by a DC motor and an IR sensor ensures that the feeding stops when the specified length has been reached. A pneumatic cylinder is used for holding the work-piece when cutting operation is done. An AC motor is used to bring about the reciprocating motion required for cutting the work-pieces. There is a self-weight attached with the reciprocating mechanism to provide the necessary downward force required for penetration of hacksaw blade in to the work-piece. When a single piece has been cut, a limit switch will get triggered by the self-weight mechanism, which is sensed by the microcontroller to start the cyclic operation again provided if the specified number of work-pieces has not been cut.

TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT

CHAPTER ONE
1.0      INTRODUCTION
1.1      BACKGROUND OF THE PROJECT
1.2      OBJECTIVE OF THE PROJECT
1.3      SCOPE OF THE PROJECT
1.4     SIGNIFICANCE OF THE PROJECT
1.5      SCOPE OF THE PROJECT
1.6      PROBLEM IDENTIFICATION
1.7      JUSTIFICATION AND RELEVANCE

CHAPTER TWO
2.0     LITERATURE REVIEW
2.1      REVIEW OF THE STUDY
2.2         REVIEW OF THE RELATED WORK
2.3      TYPES OF HACKSAWING
2.4      FEATURES OF MODERN HACKSAW
2.5      DESCRIPTION OF HACKSAW
2.6      HISTORICAL BACKGROUND OF THE STUDY

CHAPTER THREE
3.0     METHODOLOGY
3.1      PROPOSED METHODOLOGY
3.2      COMPONENTS USED AND CALCULATIONS
3.3      DESCRIPTION OF THE HACKSAW MACHINE

3.4 DESCRIPTION OF THE PROJECT SETUP

3.5      WORKING OF THE PROJECT
a.   Acquiring data from the user
b.   Sequence of operation
3.6      COST OF PRODUCTION

CHAPTER FOUR
RESULT ANALYSIS
4.0      CONSTRUCTION PROCEDURE AND TESTING
4.1      CASING AND PACKAGING
4.2      ASSEMBLING OF SECTIONS
4.3      MOUNTING PROCEDURE
4.4      TESTING OF SYSTEM OPERATION

CHAPTER FIVE     
5.0      CONCLUSION, FUTURE SCOPE, AND REFERENCES
5.1      CONCLUSION AND FUTURE SCOPE
5.2      REFERENCES

 

CHAPTER ONE
1.1                                                      INTRODUCTION
Power hacksaws are used to cut large sections of metal or plastic shafts and rods. Cutting of solid shafts or rods of diameters more than fifteen millimeters is a very hard work with a normal hand held hacksaw. Therefore power hacksaw machine was invented during 1920s in the United States to carry out the difficult and time consuming work. This motorized chain power hacksaw machine is considered as an automatic machine because the operator need not be there to provide the reciprocating motion and downward force on the work-piece in order to cut it. Once the operator has fed the work-piece till the required length in to the machine and starts the machine, then the machine will cut until the work-piece has been completely cut in to two pieces.
The fact that the operator has to feed the work-piece to the required length in to the vice is one aspect that motivated us to automate the feeding of work-piece automatically. Another one aspect is that after a shaft has been cut for one time, the operator has to unload the work-piece and advance the rest of the work-piece to the required length again and again till the end of the work-piece is reached. The Power hacksaw machine though being able to cut the shaft or rod without requiring any human effort to cut, it does require a human intervention to feed the work-piece many times with measurements being taken each time before feeding. Therein, arose a need to completely automate the process of cutting, and here we are with a proposal which will aid in eliminate the effort of the people associated with it.
In this particular project, a motorized chain hacksaw machine was designed. In this machine, the conveyor motor will get stopped by the microcontroller when the IR sensor has sent the necessary number of pulses to the microcontroller in relation to the user specified length of the work-piece. When the teeth of the rotating disc attached to the conveyor roller pass before the IR sensor, the IR sensor provides a pulse to the controller. The rotation of disc from one tooth to the next teeth means that the corresponding linear movement is one centimeter.

1.2                                       BACKGROUND OF THE PROJECT
General A hacksaw is a handheld tool used to cut through materials like plastic tubing and metal pipes. Its cutting mechanism is provided by removable blades which feature sharp teeth along their outer edge. In most cases, a hacksaw consists of a metal frame that resembles a downward- facing. A handle of plastic, wood, or metal is typically affixed to one end of the frame. The frame’s ends feature adjustable pegs that can be tightened to secure a blade in place, and loosened to remove it. Hacksaw blades are long, thin strips of hardened steel that feature a row of teeth along their cutting edge. Each end of the blade is punched with a small hole that fits onto the saw frame’s pegs. Most blades range in length from ten to 12inches (25.4 to 30.48 cm), although six-inch (15.24 cm) blades can be purchased to fit smaller hacksaw models.

1.3                                           OBJECTIVE OF THE PROJECT
The objective of this work is:

• To cater to the issue of competition in mechanical industry the need for automation is assess by all the industry.
• To identify the key policy avenues considered to be appropriate to meet the challenge of sustainable manufacturing and packaging industry for the future.
• To provide alternative for industries aiming toward reducing human effort and improvement in material handling system by implementing automation.
• Sustainable and practical automation solutions for the future industrial environment.

1.4                                         SIGNIFICANCE OF THE PROJECT
A device that applies force, changes the direction of a force, or changes the strength of a force, in order to perform a task, generally involving work done on a load. This machine is often designed to yield a high mechanical advantage to reduce the effort needed to do that work. A simple machines a wheel, a lever or an inclined plane. All other machines can be built using combinations of these simple machines.

• The machine can solve the problem of time consumption.
• Waste of resources in face of labor cost is reduced.
• The machine can be used in the industry where it is manufactured, at the packaging sector.
•  And it is used as hardware in large quantity like in fabrication of machine
• It provide alternative for industries aiming toward reducing human effort
•  It generates sustainable and practical automation solutions for the future industrial development.

1.5                                                 SCOPE OF THE PROJECT
This machine was built around an AT89C51 microcontroller, IR sensor, LCD, motor conveyor, etc. The conveyor motor will get stopped by the microcontroller when the IR sensor has sent the necessary number of pulses to the microcontroller in relation to the user specified length of the work-piece. When the teeth of the rotating disc attached to the conveyor roller pass before the IR sensor, the IR sensor provides a pulse to the controller. The rotation of disc from one tooth to the next teeth means that the corresponding linear movement is one centimeter.

1.6                                             PROBLEM IDENTIFICATION
The motorized chain power hacksaw machines, which are operated by human operators as aforementioned, have the demerit of unloading and loading the work-piece many times. In industries manufacturing pumps, these machines are used to cut the motor shafts to the required lengths. It will be difficult for the operator if he has been assigned to cut a huge quantity of motor shafts and he has to measure the lengths each time for cutting. Since humans are not as versatile as machines, there is a possibility that there may be inaccuracies. Besides, if there is a slight time delay in between every cycle of cutting a piece, the cumulative delay in time will be found to have a considerable magnitude, which might  have been utilized properly if the proposed machine were in use there.

1.7                                         JUSTIFICATION & RELEVANCE
We have found a power motorized chain power hacksaw machines to be the most useful for general shop work. Modern heavy- duty hacksaw machines provide an economical and efficient means of sawing a wide range of materials and stock sizes. motorized chain power hacksaw machines are getting rarer all the time but they do a good job within their capacity. If you can get one that takes standard hacksaw blades then you'll have a tremendous range of blades to choose from and will be able to cut most anything. Hacksaws are more tolerant to tensioning maladjustment and run off. A major advantage of power hacksawing is the relatively low capital investment required. Tooling and maintenance costs are low. Accuracy and finishes produced, range from fair to good depending on the material being sawed. Time saving as compared to simple hacksaw. Comfortable then ordinary hacksaw.

CHAPTER FIVE
   5.1                                 CONCLUSION AND FUTURE SCOPE
It is known that conventional power hacksaw machine can be replaced with motorized chain hacksaw machine. motorized chain hacksaw machine gives high productivity in short time period in comparison with the conventional power hacksaw machines. The major advantage of this machine is intervention of labor is reduced to maximum level. In this rapid emerging industrial section the use of power Hacksaw machine is wide, time and labor plays a major role in production process. This can be overcome by using this type of automated machines.
The motorized chain hacksaw machine can be made use of at any of the industries like pump manufacturing industries that involve bulk amount of shafts that have to be cut frequently. The range of size of work-pieces that can be cut using the automated hacksaw machine can be varied by changing the blade size. Currently, the machine uses 12 inch blade for cutting. An another advancement that can be implemented in automated hacksaw machines is that the user can also get cut work-pieces of different lengths in one cycle itself. This means that the user has to specify the number of work- pieces that have to be cut in each of the different length values specified. This will be possible with the help of an advanced microcontroller than AT89C51, which should have high programmable memory.

 

---

CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and fabrication of a motorized chain hacksaw with infrered sensor" is also available. Order full work to download. Chapter two of "design and fabrication of a motorized chain hacksaw with infrered sensor" consists of the literature review. In this chapter all the related work on "design and fabrication of a motorized chain hacksaw with infrered sensor" was reviewed.

CHAPTER THREE: The complete chapter three of "design and fabrication of a motorized chain hacksaw with infrered sensor" is available. Order full work to download. Chapter three of "design and fabrication of a motorized chain hacksaw with infrered sensor" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of "design and fabrication of a motorized chain hacksaw with infrered sensor" is available. Order full work to download. Chapter four of "design and fabrication of a motorized chain hacksaw with infrered sensor" consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of "design and fabrication of a motorized chain hacksaw with infrered sensor" is available. Order full work to download. Chapter five of "design and fabrication of a motorized chain hacksaw with infrered sensor" consist of conclusion, recommendation and references.

 

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

---

For more information contact us through any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp No :+2348146561114

Email Address :engr4project@gmail.com

---

FOLLOW / VISIT US VIA: