DESIGN AND FABRICATION OF INDUSTRIAL CONVEYOR USING CRANK MECHANISM
USER'S INSTRUCTIONS: The project work you are about to view is on "design and fabrication of industrial conveyor using crank mechanism" Please, sit back and study the below research material carefully. This project topic "design and fabrication of industrial conveyor using crank mechanism" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and fabrication of industrial conveyor using crank mechanism" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and fabrication of industrial conveyor using crank mechanism" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
DESIGN AND FABRICATION OF INDUSTRIAL CONVEYOR USING CRANK MECHANISM
BY
---
EE/H2013/01430
DEPARTMENT OF ELECTRICAL AND ELECTRONICS ENGINEERING
SCHOOL OF ENGINEERING
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work, "design and fabrication of industrial conveyor using crank mechanism" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on Electrical and Electronics Engineering has been approved.
By
Engr. --- Engr. ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
Engr. ---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work "design and fabrication of industrial conveyor using crank mechanism" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and fabrication of industrial conveyor using crank mechanism" visible for everyone, then the complete material on "design and fabrication of industrial conveyor using crank mechanism" is to be ordered for. Happy viewing!!!
This machine is basically works on the principle of Single Slider Crank Mechanism. Which is the heart of this machine and it converts rotary motion into a reciprocating motion. Here Fabricated the conveyor using crank mechanism machine, this project can be utilized in industry. Industries in worldwide use conveyors as a mechanism to transport boxes from place. This mechanism do not includes strong belts, pulleys and heavy motors to rotate the pulley to move the conveyor. As an alternative to this conveyor type, more simple and comfortable machine using four bar mechanism can be used. This box shifting machine helps in transfer of boxes smoothly by use of four bars with a simple arrangement. The four bar mechanism includes four links. One link is fixed and the other links act as crank, follower and connecting rod. The rotary motion of the crank is transferred to the follower by using connecting rod and is converted to the same rotary motion. This machine requires an electric motor to provide input to the system.
CHAPTER ONE
INTRODUCTION
There has been a serious demand for intermittent movement of packages in the industries right from the start. Though the continuous movement is more or less important in the same field the sporadic motion has become essential .The objective of our project is to produce a mechanism that delivers this stop and move motion using mechanical linkages. The advantage of conveyor system is that the system has a time delay between moving packages and this delay can be used to introduce any alterations in the package or move the package for any other purpose and likewise. While in conveyor system such actions cannot be performed unless programmed module is used to produce intermittent stopping of the belt which basically is costly. The prototype design requires electric motor, shafts and the frame of which the frame and platform on which the packages are moved is fabricated. All the links are being made of Aluminium which reduces the weight of the whole system including the head which has a direct contact with the boxes being moved. The system is expected to move as heavy packages as 2 to 3kgs approximately.
This machine is basically works on the principle of Single Slider Crank Mechanism which is the heart of this machine and it converts rotary motion into a reciprocating machine to crush the Cans/Plastic bottles. In this, link 1 is fixed and link 2 which is a crank is rotating about fixed link 1 and converts this rotary motion into the reciprocating motion of slider (corresponds to the link 4) by means of connecting rod which corresponds to the link 3. This is the inversion of single slider crank which is obtained by fixing link.
About material Handling Starting from the time, raw material enters the factory gate and goes out of the factory gate in the form of finished products, it is handled at all stages between, no matter it is in stores or on shop floor. It has been estimated that average material handling cost is roughly 20 to 60 % of the total cost. It thus, becomes clear that the cost of production of an item can be lowered considerably by making a saving in the material handling cost.
The aim of this project is to fabricate the box moving mechanism, which can make easier to move boxes from one section to the other while processing in the factories. In a workstation, an assembly line in order to obtain the required production rate and to achieve a minimum amount of idle time.
1.3 OBJECTIVE OF THE PROJECT
The objective of this work is to: Fabricate a Box transport mechanism which can move things from one place to another Understand project planning and execution. Understand the fabrication techniques in a mechanical workshop. Understand the usage of various mechanical machine tools and also measuring tools.
1.4 PURPOSE OF THE PROJECT
The purpose of this work is to have an easy moving in-and-out of products from one section to the other while processing in the factories.
1.5 APPLICATION OF THE PROJECT
i. We can use this mechanism in medical production fields. We can use this mechanism in bottle filling process. We can use this mechanism in cool drinks production companies.
1.6 ADVANTAGES OF THE PROJECT
i. Lubricants not required.
ii.
Simple to construct.
iii.
Low speed motor is sufficient
iv.
Easy maintenance.
v.
Less skilled operator is sufficient.
vi.
Noise of operation is reduced
1.7 SCOPE OF THE PROJECT
In this machine can comfortable for moving the product from one place to another place with safely. The machine is placed and working process is very easy for using persons. In this machine, the control unit is control the motor drive for rotation of the crank shaft .The motor is placed and the crank shaft is attached with the motor with the help of bearing. The products are safely placed in the stored place and then motor is ON. The crank is rotated and the first box is move from first place to second place in the first rotation, after that the second box is placed in the first position, the second rotation is started the first box is move from second place to third place , in the mean time the second box is move from first place to second place . In this based the boxes are move from one place to another place simultaneously .The products are safely transfer from one place to another in conveyor using crank mechanism.
1.8 PROBLEM OF THE PROJECT
The problem of the system is the high wear on conveyor drive components due to the repeated acceleration and deceleration required to move goods along the conveyor. Accordingly, prior art linear motion conveyors are frequently designed and constructed in an oversized or "beefed-up" manner to obtain reasonable reliability and acceptable maintenance levels. This oversizing practice inherently increases the cost and weight of the entire conveyor system.
CHAPTER TWO: The complete chapter two of “design and fabrication of industrial conveyor using crank mechanism” is available. Order full work to download. Chapter two of “design and fabrication of industrial conveyor using crank mechanism” consists of the literature review. In this chapter all the related work on “design and fabrication of industrial conveyor using crank mechanism” was reviewed.
CHAPTER THREE: The complete chapter three of “design and fabrication of industrial conveyor using crank mechanism” is available. Order full work to download. Chapter three of “design and fabrication of industrial conveyor using crank mechanism” consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of “design and fabrication of industrial conveyor using crank mechanism” is available. Order full work to download. Chapter four of “design and fabrication of industrial conveyor using crank mechanism” consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of design and construction of a “design and fabrication of industrial conveyor using crank mechanism” is available. Order full work to download. Chapter five of “design and fabrication of industrial conveyor using crank mechanism” consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view our related construction (or design) picture.
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.