USER'S INSTRUCTIONS: The project work you are about to view is on "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back". Please, sit back and study the below research material carefully. This project topic "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

 

BY

---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

---

APPROVAL PAGE

This is to certify that the research work, "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" visible for everyone, then the complete material on "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" is to be ordered for. Happy viewing!!!

---

This work is on design and construction of an android or cell phone charger with auto cut off feature. This device is designed to charge cell phone, that charges battery automatically, when the battery is charged it will shut off the charger.
The objective of this project is to design and construct an electronic device that will supply electrical energy (charges) to a cell phone battery, in a process to restore the battery's used up energy which will automatically shut-off immediately the battery is fully charged.

 

TABLE OF CONTENTS

 TITLE PAGE

APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT

CHAPTER ONE

• INTRODUCTION
• BACKGROUND OF THE PROJECT
• PROBLEM STATEMENT
• AIM/OBJECTIVE OF THE PROJECT
• SIGNIFICANCE OF THE PROJECT
• APPLICATION OF THE PROJECT
• LIMITATION OF THE PROJECT
• ADVANTAGES OF THE PROJECT
• METHODOLOGY
• PROJECT ORGANISATION

CHAPTER TWO

LITERATURE REVIEW
2.1      REVIEW OF BATTERY CHARGER
2.2      HISTORICAL BACKGROUND OF BATTERY CHARGER
2.3      REVIEW OF RECHARGEABLE BATTERY
2.4      REVIEW OF CHARGER UNITS
2.5      REVIEW OF DIFFERENT TYPES OF BATTERY CHARGERS
2.6      REVIEW OF CELL PHONE BATTERY

CHAPTER THREE

3.0     CONSTRUCTION METHODOLOGY

3.1     INTRODUCTION

3.2     BLOCK DIAGRAM OF THE SYSTEM

3.3      CIRCUIT DIAGRAM
3.4      CIRCUIT DESCRIPTION
3.5      SYSTEM OPERATION
3.6      DESCRIPTION OF MAJOR COMPONENTS USED

CHAPTER FOUR

RESULT ANALYSIS

4.1      CONSTRUCTION PROCEDURE AND TESTING
4.2      CASING AND PACKAGING
4.3      ASSEMBLING OF SECTIONS
4.4      TESTING OF SYSTEM OPERATIONOBSERVATIONS
4.6     DIFFICULTIES ENCOUNTERED ON THE SYSTEM
4.7      COST OF PRODUCTION

CHAPTER FIVE

• SUMAMRY
• CONCLUSIONS/SUGGESTIONS

5.3     REFERENCES
CHAPTER ONE
1.0                                                        INTRODUCTION
1.1                                         BACKGROUND OF THE PROJECT
An auto turn cutoff charger is an electrical device employed in charging cell phone batteries known as “lithium-ion battery”. This charger automatically shut off the charger through a relay whenever battery attains full charge. This prevents the deep charge of the battery. If the battery voltage is below the set value, then circuit automatically charges the battery.
An Auto cutoff battery charger is a good option for people who don’t like having to mess with the battery charging process too much. Simply hook the battery up to an Auto cut off battery charger and it will proceeds to charge our cell phone battery automatically. When the battery is charged it will shut off. Hooking a battery up to an Auto turn off battery charger is really easy too. Simply hook the alligator clips up to the battery posts and leave the Auto turn off battery charger plugged in. A battery will never get overcharged with an Auto turn off battery charger. Many people choose an Auto turn off battery charger over a manual battery charger can fry our batteries by not shutting off when the battery is charger up. This can cause a lot of headaches and prevent us from getting the life expectancy out of the batteries we purchase.
1.2                                                  PROBLEM STATEMENT
In the last decade cellphone battery charger was built only to charge and keep charging the battery even when the battery is fully charged, and this exposes the battery to overcharge and explosion, this can also cause a lot of headaches and prevent us from getting the life expectancy out of the batteries we purchase. To solve this problem, an auto-cutoff of charger was built. With an auto cutoff battery charger, cellphone battery will never get overcharged.
1.3                                        OBJECTIVES OF THE PROJECT
The main aim of this work is to build a charger that will automatically shut off the charger when battery attains full charge. The objectives are:

• To prevents the deep charge of the battery.
• To automatically control the charging process of a charger
• To protect the charger from explosion.

1.4                                      SIGNIFICANCE OF THE PROJECT
Building this device will serve as a way of protecting our investmentby ensuring that our charger and battery is safe. This study makes it possible for me to learn how to build a charging circuit which is simple, easy to use and components are easily available and at low cost.
1.5                                         APPLICATIONS OF THE PROJECT
This battery charger with little modifications can charge any battery ranging from 0 to 15V. Some of the applications are Rechargeable Cells Motorcycle Batteries Car Batteries, andmobile phone battery.

1.6                                           LIMITATION OF THE PROJECT
Subjecting a discharged cell to a current in the direction which tends to discharge it further to the point the positive and negative terminals switch polarity causes a condition called cell reversal. Generally, pushing current through a discharged cell in this way causes undesirable and irreversible chemical reactions to occur, resulting in permanent damage to the cell. Cell reversal can occur under a number of circumstances, the two most common being:

• When a battery or cell is connected to a charging circuit the wrong way around.
• When a battery made of several cells connected in series is deeply discharged.

In the latter case, the problem occurs due to the different cells in a battery having slightly different capacities. When one cell reaches discharge level ahead of the rest, the remaining cells will force the current through the discharged cell.
Many battery-operated devices have a low-voltage cutoff that prevents deep discharges from occurring that might cause cell reversal.
Cell reversal can occur to a weakly charged cell even before it is fully discharged. If the battery drain current is high enough, the cell's internal resistance can create a resistive voltage drop that is greater than the cell's forward emf. This results in the reversal of the cell's polarity while the current is flowing. The higher the required discharge rate of a battery, the better matched the cells should be, both in the type of cell and state of charge, in order to reduce the chances of cell reversal.
In some situations, such as when correcting Ni-Cad batteries that have been previously overcharged, it may be desirable to fully discharge a battery. To avoid damage from the cell reversal effect, it is necessary to access each cell separately: each cell is individually discharged by connecting a load clip across the terminals of each cell, thereby avoiding cell reversal.
1.7                                         METHODOLOGY
To achieve the aim and objectives of this work, the following are the steps involved:

• Study of the previous work on the project so as to improve it efficiency.
• Draw a block diagram.
• Test for continuity of components and devices,
• Design and calculation for the device was carried out.
• Studying of various component used in circuit.
• Construction of the circuit was carried out.
• Finally, the whole device was cased and final test was carried out.

1.8                                                         PROJECT ORGANISATION
The work is organized as follows: chapter one discuses the introductory part of the work,   chapter two presents the literature review of the study,  chapter three describes the methods applied,  chapter four discusses the results of the work, chapter five summarizes the research outcomes and the recommendations.

CHAPTER FIVE
5.1                                                           CONCLUSION
Having carefully selected the entire component that are required for the construction of the charger and built according to the circuit diagram we were able to design and construct a workable battery charger.
This charger is designed for cell phone; otherwise the charge output voltage will not be sufficient to carry out any meaniful charging operation.        
As with any charger it must be housed in a clean environment and operations should be by will trained individual. 
Protective materials should be worn while charging batteries to avoid danger to health as a result of the gassing from the battery as the gas are highly inflammable.
5.2      CONCLUSION/SUGGESTION FOR FURTHER IMPROVEMENT
Using this system when the battery is fully charged it will shut off automatically. The circuit consists of very less components and simple in design. Whether we have marine batteries, motorcycle batteries, car batteries or other sources of electricity that need to be charged up, we can count on quality auto turn-off battery charges to add many years of life through the cycling cycles.
In the implementation of this project what has proved most difficulties is the selection of the right value of components some were using two diode (the maraine value), in order to have a perfect full wave rectification, we made use of four diodes and the and a functional portable battery is been designed and constructed.
The charger is very simple to use, ever to a Longman all he needs is just a little instruction and it will be accustomed to its method of working.
There is still further improvement demanded from use, mostly in the area of building a work complex and functions charger that could charge cells of higher voltage that might ranges to 48 volts and be able to charge more than two or three battery at the same time having more than one terminal.
Due to the possibility of this, it has surely put smiles on the face of most people like some motorist who has long been finding it difficult charging their own batteries at their homes and at their convenient time.

 

---

CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" is also available. Order full work to download. Chapter two of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" consists of the literature review. In this chapter all the related work on "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" was reviewed.

CHAPTER THREE: The complete chapter three of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" is available. Order full work to download. Chapter three of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" is available. Order full work to download. Chapter four of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" is available. Order full work to download. Chapter five of "design and implementation of 5v dc li-ion battery (android phone) charger with automatic control feed back" consist of conclusion, recommendation and references.

 

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

---

For more information contact us through any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp No :+2348146561114

Email Address :engr4project@gmail.com

---

FOLLOW / VISIT US VIA: