USER'S INSTRUCTIONS: The project work you are about to view is on ''design and simulation of fourth order active band stop filter'' .Please, sit back and study the below research material carefully. This project topic ''design and simulation of fourth order active band stop filter'' have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this ''design and simulation of fourth order active band stop filter'' project research material is to reduce the stress of moving from one school library to another all in the name of searching for ''design and simulation of fourth order active band stop filter'' research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

 

BY

---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

---

APPROVAL PAGE

This is to certify that the research work ''design and simulation of fourth order active band stop filter'' by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work ''design and simulation of fourth order active band stop filter'' research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of ''design and simulation of fourth order active band stop filter'' visible for everyone, then the complete material on ''design and simulation of fourth order active band stop filter'' is to be ordered for. Happy viewing!!!

---

This seminar is ondesigned and simulation of an active fourth order active band stop filter. The filter isdesigned such that it has butter worth response. The topologies that will be used to implement the filterare the multiple feedback (MFB). The filter is designed for radio frequency identification (RFID) system reader to reject all signalsoutside the band (10-20) kHz and to amplify the low antenna signal. This is because the identificationnumber signals which are transmitted from the tag of RFID are (12.5 kHz) and (15.65 kHz).So the passband of the filter is taken to be (10-20) kHz. The values of the resistors and capacitors of the filtercircuit are calculated and the circuits are then simulated withtheMULTISIMprogramtoreachthefinalconclusionwhichdescribestheresultofsimulationcomparedtothe simulationofthe transferfunctionofthe filterusingMUTLABprogram.

TABLE OF CONTENTS
Cover page/Title page
Certification page
CHAPTER ONE

• Introduction
• Background of the Study
• Problem Statement
• Aims and Objective
• Significance of the study
• Applications of fourth order active band stop filter
• Advantages of fourth order active band stop filter

CHAPTER TWO

• Literature Review
• Overview of a filter
• Different types of electronic filter
• Overview of a band stop filter
• Types of band stop filters
• Types of band stop filters
• Working Principle Of A Band Stop Filter
• Review Of Related Studies

CHAPTER THREE

• Method
• Fourth order active band stop filter design
• Fourth-orderorder active band filterdesignimplementation
• NImultisimimplementation
• Matlabimplementation
• Resultsandanalysis
• Conclusion

Reference  

CHAPTER ONE
1.0                                                      INTRODUCTION
1.1                                         BACKGROUND OF THE STUDY
Radio Frequency Identification (RFID) is an enabling technology for remotelyidentifying,monitoring,and tracking various objects of interest using radio wavetransmissions.Theautomaticidentificationofobjectsispossiblebywirelesscommunications between a tag (attached to an object) and its reader (interrogator) atdistantlocation(Gleich et al., 2015).
A typical RFID system is comprised of the following components (Buzug et al., 2012):

• Oneormoretagsortransponderswithuniqueidentificationcodesandasmallantennaembeddedwithineachtag.
• Areader,orinterrogator,withoneormoreantennasthatareconnectedtoahostcomputerthroughvarious kindsofinterfaces.

Ataghasanidentificationnumber(ID)andareaderrecognizes an objectthroughconsecutivecommunicationswiththetagattachedtoit.Thereadersendsouta signal which supplies power and instructions to a tag. The tag transmits its ID to thereader and the reader consults an external data base with received ID to recognize theobject(Buzug et al., 2012).
An active band-pass filter is used for the RFID system reader to reject all signalsoutside the (10-20) kHz signals and to amplify the low antenna signal. These arebecausetheIDsignalsfromthetagare(12.5kHz)and(15.65kHz)andsignalpowerisverylow (Biederer et al., 2019).
In this paper, RFID system is considered with 125 kHz, FSK modulation scheme. Inlow frequency RFID system, analog active filters are used because of the followingadvantages (Biederer et al., 2019):

• The maximum gain or the maximum value of the transfer function may be greaterthanunity.
• The loading effect is minimal, which means that the output response of the activefilter isessentiallyindependentoftheloaddrivenbythefilter.
• Active filters can be smaller, lighter, and more accurate than passive filters whichcan be large and heavy at low frequencies if inductors arerequired.
• Higherorderfilterscaneasilybecascadedsinceeachop-ampcanbesecondorder.

The simplest design of a band-pass filter is the connection of a high-pass filterandalowpassfilterinseries,whichiscommonlydoneinwide-bandfilterapplications. Thus, a first order high-pass and a first-order low-pass provide a second-order band-pass, while a second-order high-pass and a second-order low-pass result ina fourth-order band-pass response. In comparison to wide-band filters, narrow-bandfilters of higher order consist of cascaded second-order band-pass filters(Biederer et al., 2019).
Themostcommon filterresponsesaretheButterworth, Tschebyscheff,andBessel types. Among these responses, Butterworth type is used to get a maximally-flatresponse. Also, itexhibits a nearly flatpass band with noripple. The roll-off issmooth and monotonic, with a low-pass or high pass roll off 20dB/dec for every pole.Thus,afourth orderButterworth band-pass filter would have an attenuation rate of40dB/decand-40dB/dec (Biederer et al., 2019).
This work is on simulation of 4th order active band stop filter. The design will be carried out in order to meet the design specifications and the simulation will be done using MATLABsimulationresultwillbediscussed.
1.2                                                  PROBLEM STATEMENT
Appliances malfunctions when a frequency is transmitted outside the required frequency band. In order to solve this problem a fourth order active band stop filter is used. The filter is designed for radio frequency identification (RFID) system reader to reject all signalsoutside the band (10-20) kHz and to amplify the low antenna signal.
1.3                                     AIM AND OBJECTIVE OF THE STUDY
The aim of this seminar is to carry out a study on design and simulation of fourth order active band stop filter. The objectives of the study are:

• To carry out a study on the workings of a fourth order active band stop filter
• Study the operation and application of filters in RFID appliances.
• To carry out a simulation using MATLAB & MULTISIM simulation.

1.4                                           SIGNIFICANCE OF THE STUDY
This study will serve a means of studying the application of filter in electronics and telecommunication.

1.5      APPLICATIONS OF FOURTH ORDER ACTIVE BAND STOP FILTER

The applications include:

• Fourth order active band stop filter is used in various speaker systems to enable and enhance audio quality.
• They are used in Telecommunications (Telephone, Digital Subscriber Line) to reduce the noise while signal transmission.
• It is reduced to clear static in radio devices.
• They are also used in instrument amplifiers, especially for acoustic instruments like Electronic Guitar in reducing the humming sound produced at 60 Hz.
• In the field of medicine, Electrocardiogram (ECG) machine also has Fourth order active band stop filter for hassle-free operations.
• They are a vital part of signal and image processing units.
• Optical Filters also have Fourth order active band stop filters for use in laser eye protection applications.
• It filters out unwanted noises from the duplexes and switches.

1.6      ADVANTAGES OF FOURTH ORDER ACTIVE BAND STOP FILTER

The advantages include:

• It offers Low Passband insertion loss and group delay.
• Unwanted Signals are effectively suppressed while Transmission.
• These Filters are preferred while transmitting high-power signals.
  

---

CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of ''design and simulation of fourth order active band stop filter'' is also available. Order full work to download. Chapter two of ''design and simulation of fourth order active band stop filter'' consists of the literature review. In this chapter all the related work on ''design and simulation of fourth order active band stop filter'' was reviewed.

CHAPTER THREE: The complete chapter three of ''design and simulation of fourth order active band stop filter'' is available. Order full work to download. Chapter three of ''design and simulation of fourth order active band stop filter'' detector consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of ''design and simulation of fourth order active band stop filter'' is available. Order full work to download. Chapter four of ''design and simulation of fourth order active band stop filter'' detector consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of ''design and simulation of fourth order active band stop filter'' is available. Order full work to download. Chapter five of ''design and simulation of fourth order active band stop filter'' detector consist of conclusion, recommendation and references.

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

---

For more information contact us through any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp No :+2348146561114

Email Address :engr4project@gmail.com

---

FOLLOW / VISIT US VIA: