USER'S INSTRUCTIONS: The project work you are about to view is on "single phase controlled rectified charger for charging automotive battery". Please, sit back and study the below research material carefully. This project topic ( single phase controlled rectified charger for charging automotive battery) have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "single phase controlled rectified charger for charging automotive battery" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "single phase controlled rectified charger for charging automotive battery" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

SINGLE PHASE CONTROLLED RECTIFIED CHARGER FOR CHARGING AUTOMOTIVE BATTERY

BY

---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

DECEMBER,2018

---

APPROVAL PAGE

This is to certify that the research work, "single phase controlled rectified charger for charging automotive battery" by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work "single phase controlled rectified charger for charging automotive battery" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "single phase controlled rectified charger for charging automotive battery" visible for everyone, then the complete material on "single phase controlled rectified charger for charging automotive battery" is to be ordered for. Happy viewing!!!

---

Controlled rectified charger for charging automotive battery is an improved battery charger circuit for rapidly charging a battery by increasing the rate of battery charge acceptance through periodic battery discharge during the charging process includes a pair of first and second controlled rectifier circuits coupled to an AC source and adapted for coupling to a battery. The first controlled rectifier circuit is rendered conductive during the charging intervals to supply the battery with charge current from the AC source. The second controlled rectifier circuit is rendered conductive during battery discharge intervals to discharge the battery in a substantially lossless manner by conducting battery discharge current through the AC source, thus realizing a highly efficient battery charger.

TABLE OF CONTENTS

 TITLE PAGE

APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRACT
TABLE OF CONTENT

CHAPTER ONE

1. INTRODUCTION
2. BACKGROUND OF THE PROJECT
3. PROBLEM STATEMENT
4. AIM/OBJECTIVE OF THE PROJECT
5. SIGNIFICANCE OF THE PROJECT
6. APPLICATION OF THE PROJECT
7. LIMITATION OF THE PROJECT
8. SCOPE OF THE PROJECT
9. PROJECT ORGANISATION

CHAPTER TWO

LITERATURE REVIEW
2.0      LITERATURE REVIEW
2.1      HISTORICAL BACKGROUND OF BATTERY CHARGER
2.2      REVIEW OF BATTERY CHARGER

2.3      REVIEW OF DIFFERENT TYPES OF BATTERY CHARGERS

2.4      REVIEW OF SILICON CONTROLLED RECTIFIER (SCR)
2.5      SCR OPERATING MODES
2.6      SCR IN FORWARD AND REVERSE CHARACTERISTICS
2.7    PARAMETERS OF SCR
2.8    OVERVIEW OF SINGLE PHASE RECTIFICATION

CHAPTER THREE

3.0      CONSTRUCTION METHODOLOGY

3.1      BLOCK DIAGRAM OF THE SYSTEM

3.2      CIRCUIT DIAGRAM
3.3      CIRCUIT DESCRIPTION
3.4      SYSTEM OPERATION

CHAPTER FOUR

RESULT ANALYSIS

4.1      CONSTRUCTION PROCEDURE AND TESTING
4.2      CASING AND PACKAGING
4.3      ASSEMBLING OF SECTIONS
4.4      TESTING OF SYSTEM OPERATION
4.5     COST OF PRODUCTION

CHAPTER FIVE

1. SUMMARY
2. CONCLUSION/SUGGESTION FOR FURTHER IMPROVEMENT

5.3     REFERENCES

CHAPTER ONE

1.1                                                     INTRODUCTION

A battery is a device which can store energy in chemical form and convert that energy into electrical energy when needed. It can be secondary (rechargeable) or primary (Non rechargeable) Rechargeable batteries have an advantage over primary batteries with the fact that they can be reused. This is possible by charging a battery, i.e. feeding energy to the secondary cell by forcing electric current through it.
A battery basically consists of number of cells, with each cell consisting of two electrodes immersed in an electrolyte solution consisting of an acid and distilled water. In charged state, one of the electrodes consists of a metal whereas the other consists of metal oxide. The acid enables flow of ions between the two electrodes.
When the battery starts discharging, electrons flow from one electrode (anode) and get accumulated at another electrode (cathode). This happens by the process of oxidation and reduction and continues till both the electrodes are devoid of reagents and the battery is completely discharged. The charging is then done externally by providing external electric current so that the anode receives electrons and the excess electrons are removed from the cathode. However a problem arises when the battery gets overcharged, this leads to more gassing effect. Even excessive discharging of a battery reduces its age.

A solution to this problem is to ensure a controlled charging method such that the battery charging and discharging is done in a controlled manner. This article describes a simple controlled battery charger using an SCR. The AC signal is rectified using a SCR.

1.2                          PROBLEM STATEMENT
The major problem with a conventional battery charger is the ability to charge quickly due to its low current circuit. This device was invented to overcome this challenge. This device rapidly charging a battery by increasing the rate of battery charge acceptance through periodic battery discharge during the charging process includes a pair of first and second controlled rectifier circuits coupled to an AC source and adapted for coupling to a battery.

1.3                AIM AND OBJECTIVES OF THE PROJECT
The main aim of the project is to design a device that will recharge 12v lead acid battery SCR as the major charging components. The objectives are:

1. to charge a motor battery direct from a rectified circuit
2. to charge an acid lead battery at higher current
3. to use few electronics components to build a battery charger.
4. to provide a battery charger circuit for rapidly charging a battery by periodically discharging the battery in a substantially lossless manner at a high rate for short intervals during the charging process.
5. to provide a battery charger for rapidly charging batteries through periodic battery discharge which is accomplished in a substantially lossless manner by conducting battery discharge current through the AC source from which it is being charged.

1.4                      SIGNIFICANCE OF THE PROJECT
This device charges 12v acid battery mainly at higher current. Working on this project has exposed us the knowledge about the applications and operation of silicon controlled rectifier.

1.5                   APPLICATION OF THE PROJECT
This battery charger is used in the following devices:

1. It is used in inverter
2. It is used in Solar energy system
3. It is used in vehicles
4. It is used in an uninterruptible power supply (UPS), etc.

1.6                        LIMITATION OF THE PROJECT
As we all know that no human effort to achieve a set of goals goes without difficulties, certain constraints were encountered in the course of carrying out this project and they are as follows:-

1. Difficulty in information collection: I found it too difficult in laying hands of useful information regarding this work and this course me to visit different libraries and internet for solution.
2. Financial Constraint:    Insufficient fund tends to impede the efficiency of the researcher in sourcing for the relevant materials, literature or information and in the process of data collection (internet).
3. Time Constraint: The researcher will simultaneously engage in this study with other academic work. This consequently will cut down on the time devoted for the research work.

1.7                           SCOPE OF THE PROJECT
The AC main voltage is given to the SCR for rectification and SCR rectifies AC main voltage. This rectified voltage is used to charge battery.
When the battery connecter to the charging circuit, the battery will not be dead completely and it will get discharged this will give the forward bias voltage to the silicon controlled rectifier.

1.9                          PROJECT ORGANISATION
The work is organized as follows: chapter one discuses the introductory part of the work,   chapter two presents the literature review of the study,  chapter three describes the methods applied, chapter four discusses the results of the work, chapter five summarizes the research outcomes and the recommendations.

---

CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "single phase controlled rectified charger for charging automotive battery" is also available. Order full work to download. Chapter two of "single phase controlled rectified charger for charging automotive battery" consists of the literature review. In this chapter all the related work on "single phase controlled rectified charger for charging automotive battery" was reviewed.

CHAPTER THREE: The complete chapter three of "single phase controlled rectified charger for charging automotive battery" is available. Order full work to download. Chapter three of "single phase controlled rectified charger for charging automotive battery" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of "single phase controlled rectified charger for charging automotive battery" is available. Order full work to download. Chapter four of "single phase controlled rectified charger for charging automotive battery" consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of design and construction of a "single phase controlled rectified charger for charging automotive battery" is available. Order full work to download. Chapter five of "single phase controlled rectified charger for charging automotive battery" consist of conclusion, recommendation and references.

 

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

For more information contact us through any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

Visit the link below to see our recent works, and SUBSCRIBE to receive notification for our electronics teachings and practicals.
https://www.youtube.com/channel/UChY9Z1-egigJbYjYnapd0nw

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp No :+2348146561114

Email Address :engr4project@gmail.com

---

FOLLOW / VISIT US VIA: