USER'S INSTRUCTIONS: The project work you are about to view is on "the design and construction of cable control device for arrangement and easy identification of cables". Please, sit back and study the below research material carefully. This project topic"the design and construction of cable control device for arrangement and easy identification of cables"have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this"the design and construction of cable control device for arrangement and easy identification of cables" project research material is to reduce the stress of moving from one school library to another all in the name of searching for"the design and construction of cable control device for arrangement and easy identification of cables"research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.

---

TITLE PAGE

 

BY

---
--/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---

---

APPROVAL PAGE

This is to certify that the research work,"the design and construction of cable control device for arrangement and easy identification of cables"by ---, Reg. No. --/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.

By
---                                                     . ---
Supervisor                                                  Head of Department.
Signature……………….                           Signature……………….        

……………………………….
---
External Invigilator

---

DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.

---

ACKNOWLEDGEMENT

The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.

---

PROJECT DESCRIPTION: This work"the design and construction of cable control device for arrangement and easy identification of cables"research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of"the design and construction of cable control device for arrangement and easy identification of cables"design and construction of an intruder detector alarm system with direction / location display"is to be ordered for. Happy viewing!!!

---

This work is on cable control device for arrangement and easy identification of cables. It is design for easy identifying fault wire. In this work IC 4017 is used as counter to display the output. The 555 timer IC is used to generate the PWM signal for 4017 IC. Both the major components are discussed along with their working in this work. A cable tester can identify if the wires are paired correctly. It can also show if there is a break in the insulation, a situation which allows crosstalk between two wires that should not be connected. The tester can also tell whether the cable has the proper level of resistance.

 

TABLE OF CONTENT
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT

CHAPTER ONE
1.0      INTRODUCTION
1.1      BACKGROUND OF THE STUDY
1.2      STATEMENT OF THE PROBLEM
1.3      AIM AND OBJECTIVES OF THE STUDY
1.4      PURPOSE OF THE STUDY
1.5      SIGNIFICANCE OF THE STUDY
1.5      SCOPE OF THE STUDY
1.6      APPLICATION OF THE STUDY

CHAPTER TWO
2.0     LITERATURE REVIEW
2.1      OVERVIEW OF THE STUDY
2.2      CABLE CONNECTIONS TEST
2.3      TESTING SHORT–CIRCUIT
2.4      DIFFERENT TYPES OF TESTER

CHAPTER THREE
3.0     CONSTRUCTION METHODOLOGY
3.1      SYSTEM BLOCK DIAGRAM          
3.2      SYSTEM CIRCUIT DIAGRAM
3.3      COMPONENTS USED
3.4      SYSTEM WORKING PRINCIPLE
3.5      POWER SUPPLY UNIT

CHAPTER FOUR
4.0      CONSTRUCTION PROCEDURE AND TESTING
4.1      CASING AND PACKAGING
4.2      ASSEMBLING OF SECTIONS
4.3      TESTING OF SYSTEM OPERATION

CHAPTER FIVE
5.0      CONCLUSION AND RECOMMENDATION     
5.1      CONCLUSION
5.2      RECOMMENDATION
REFERENCES

 

 

CHAPTER ONE
1.0                                                        INTRODUCTION
1.1                                            BACKGROUND OF THE STUDY
The idea behind the design and construction of this system is to make available or alternative means providing safety and accuracy demand in flow of signals in network cables. This goes a long way in helping to curb the problem frequently encountered as a result of open circuit and unwanted connection, in the wire (Anis et al., 2017).
When connected to an Ethernet cable, a cable control device tells if the cable is capable of carrying an Ethernet signal. If the cable carries the signal, this indicates that all the circuits are closed, meaning that electric current can move unimpeded through the wires, and that there are no short circuits, or unwanted connections, in the wire. Cable control device vary in complexity and price, but a basic tester consists of a source of electrical current, a measuring device that shows if the cable is good, and a connection between the two, usually the cable itself (Anis et al., 2017).
Cable control device used in Ethernet cable allows computers in the network to “talk” to each other. An Ethernet cable has wires that are arranged in pairs. For current to flow correctly, the wire pairs must be connected in the proper order.
A cable control device can identify if the wires are paired correctly. It can also show if there is a break in the insulation, a situation which allows crosstalk between two wires that should not be connected. The system can also tell whether the cable has the proper level of resistance (Guoqiang et al., 2013).
If a network isn’t working correctly, the problem is frequently user error or other problems. It will rarely be a faulty cable. A cable control device is more frequently used to tell whether a patch cable will work before it is connected. The cabling should first be examined visually to identify any obvious problems. If everything looks correct, a cable control device may then be used.
A cable control device is a simple apparatus that merely identifies whether current flows through the cable, or it may be a professional-level, complex device that gives additional information that helps identify the problem. Professional-level cable control device may not only tell if an open circuit exists, but may identify where the break is located. Some also identify the gauge of wire used and can generate their own signal to test for interference (Harfoush et al., 2013).
Basic cable control device can test for simple connectivity issues but may not identify other problems that cause the cable to malfunction (Christhu , 2015). Cabling may not work when it is near a source of interference or if the cable is too long. Intermittent faults may develop that do not show up when the cable is tested. Sometimes the problem is not sustained long enough to show up on the tester.

1.2      STATEMENT OF THE PROBLEM
Several studies have shown that the majority of network performance problems occur in or near the users’ desktop/laptop computer.  These problems include, but are not limited to, duplex mismatch conditions on Ethernet/FastEthernet links, incorrectly set TCP buffers in the user’s computer, or problems with the local network infrastructure.  The work is designed to quickly and easily identify a specific set of conditions that are known to impact network performance (Begg et al., 2016).  A multi-level series of plain language messages, suitable for novice users, and detailed test results, suitable for a network engineer, are generated and available to the user.  Finally, the test results may be easily emailed to the appropriate administrator to assist in the problem resolution phase.
Another problem is the inability of the testing personnel to use the instrument accurately. When these tester is not used accurately that means that an incorrect result is expected to be seen (Christhu , 2015).

1.3                                  AIM AND OBJECTIVES OF THE PROJECT
The aim of this study is to build a low cost cable control device. The objectives of the study are:

• To build the system prototype at low cost
• To easily identify faulty cables
• To verify that all of the intended connections exist and that there are no unintended connections in the cable being tested.

1.4                                              PURPOSE OF THE PROJECT
The purpose of this work is to design and construct a cable control device that can be used to identify if the wires are paired correctly. It can also show if there is a break in the insulation, a situation which allows crosstalk between two wires that should not be connected, which can  also tell whether the cable has the proper level of resistance.

1.5                                SIGNIFICANCE OF PROJECT
This study will serve as an easier means of identifying and arranging cables thereby making computer network easier for users to share multiple resources and access shared files. This study will also serve as an avenue of making student involved becoming familiar with 555 timer and decade counter connections and operation.

1.6                                                   SCOPE OF THE STUDY
The scope of this work covers building a system that is use for easy identifying fault wire. In this work IC 4017 is used as counter to display the output. The 555 timer IC is used to generate the PWM signal for 4017 IC. Both the major components are discussed along with their working in this work.

1.7                                          APPLICATIONS OF THE SYSTEM

• It can be used for telephone wires and for network cable RJ45 testing and fault identification.
• It conducts two tests, i.e., master and remote that can take a role in analysis easier.
• It can be used for identifying the improper connection wires or short-circuit point in the cable.

CHAPTER FIVE       
5.0      CONCLUSION
The course of undergoing this project has disclosed numerous important things about computer cable tester. Ranging from its economic importance and recommendation based on the use of this tester. Hence with the successful design and construction of this project, a more efficient way of ensuring continuous and easy identification of cables.  
 
5.1      RECOMMENDATION
This project is designed to be used in our homes, offices and industries where the need for steady flow of network in our computers and safety is needed. And should be used and maintain by a qualified personnel.

 

---

CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of"the design and construction of cable control device for arrangement and easy identification of cables"is also available. Order full work to download. Chapter two of"the design and construction of cable control device for arrangement and easy identification of cables"consists of the literature review. In this chapter all the related work on"the design and construction of cable control device for arrangement and easy identification of cables"was reviewed.

CHAPTER THREE: The complete chapter three of"the design and construction of cable control device for arrangement and easy identification of cables"is available. Order full work to download. Chapter three of"the design and construction of cable control device for arrangement and easy identification of cables"consists of the methodology. In this chapter all the method used in carrying out this work was discussed.

CHAPTER FOUR: The complete chapter four of"the design and construction of cable control device for arrangement and easy identification of cables"is available. Order full work to download. Chapter four of"the design and construction of cable control device for arrangement and easy identification of cables"consists of all the test conducted during the work and the result gotten after the whole work

CHAPTER FIVE: The complete chapter five of"the design and construction of cable control device for arrangement and easy identification of cables" is available. Order full work to download. Chapter five of"the design and construction of cable control device for arrangement and easy identification of cables" consist of conclusion, recommendation and references.

 

---

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

---

For more information contact us through any of the following means:

Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

---

COUNTRIES THAT FOUND OUR SERVICES USEFUL

Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124

Watsapp No :+2348146561114

Email Address :engr4project@gmail.com

---

FOLLOW / VISIT US VIA: