An electronic bell is a signaling device typically placed near an entry door to a building. When a visitor presses a button the bell rings inside the building, alerting the occupant to the presence of the visitor. Modern house bells are electric — they are actuated by an electric switch.
In most wired systems, a button on the outside next to the door, located around the height of the doorknob, activates a signaling device (usually a chime, bell, or buzzer) inside the building. Pressing the electronic bell button, a single-pole, single-throw (SPST) pushbutton switch momentarily closes the doorbell circuit. The function of the indicator is to indicate when someone is pressing the button.
 

TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
ABSTRACT
TABLE OF CONTENT

CHAPTER ONE
1.0     INTRODUCTION
1.1     OBJECTIVE OF THE PROJECT
1.2     SIGNIFICANCE OF THE PROJECT
1.3     LIMITATION OF THE PROJECT
1.4     PROJECT ORGANISATION

 

CHAPTER TWO
2.0     LITERATURE REVIEW
2.1     REVIEW OF DOORBELL
2.2   HISTORICAL BACKGROUND OF THE PROJECT
CHAPTER THREE
3.0     CONSTRUCTION
3.1     SYSTEM BLOCK DIAGRAM
3.2      SYSTEM OPERATION
3.3       CIRCUIT DESCRIPTION
3.4     DESCRIPTION OF COMPONENTS USED

CHAPTER FOUR
RESULT ANALYSIS
4.0     CONSTRUCTION PROCEDURE AND TESTING
4.1     CASING AND PACKAGING
4.2     ASSEMBLING OF SECTIONS
4.3     TESTING OF SYSTEM OPERATION
4.4      COST ANALYSIS

CHAPTER FIVE     
5.0     CONCLUSION
5.1     RECOMMENDATION
5.2     REFERENCES

 

CHAPTER ONE
1.1                                          INTRODUCTION
To cleanly understand the wood information technology and communication which is the life blood of all human activities the assimilation of communication technology is of great important. The development of communication technology in any nation makers communication technology easy and pleasant. And one of basic building block of a communication system is the house bell indicating which serves as inter-call light to ensure proper communication within an officer or domestic.

An electronic bell can be defined as dunce which can be use to alert signal for indicating of problem in alarm signals.
The device is classified according to were types, mode of operation and the application there are numerous types of alarming signals but for the purpose of this project an electric bell with light indicator is considered.
This device receives its input signal form an electrical device known as bell push. That was connected at the wing board Via joint box. The signal (current) passes through the wire and fed into the bell which causes the bell to ring in order to alert the receiver. 
Furthermore, the objective of this electronic bell is to provide a cheap and continent means of communication between two or more people in the same premises.

The major different between inter- communication system using telephone and electric bell is that the signal is transmitted by the call indicator system in place of speech as in the case of the telephony.
In most wired systems, a button on the outside next to the door, located around the height of the doorknob, activates a signaling device (usually a chime, bell, or buzzer) inside the building. Pressing the electronic bell button, a single-pole, single-throw (SPST) pushbutton switch momentarily closes the doorbell circuit. One terminal of this button is wired to a terminal on a transformer. A doorbell transformer steps down the 240-volt AC electrical power to a lower voltage, typically 10 to 20 volts.  

1.2                              OBJECTIVE OF THE PROJECT
The objective of this electronic bell is to design a device that will provide a cheap and continent means of communication between two or more people in the same premises. In electric bell, the signal is transmitted by the call indicator system is to...

1.3                              SIGNIFICANCE OF THE PROJECT
Electronic bell Provide a cheap and continent means of communication between two or more people in the same premises. It can also be used in offices or industries as a mean alerting of someone.

1.4                                           LIMITATION OF THE PROJECT

This project operates with power supply, which means that the system will stop working whenever mains power supply fails.

1.5                          PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to electronics bell. In this chapter, the background, significance, objective limitation and problem of electronics bell box were discussed.
Chapter two is on literature review of an electronics bell. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.

 

---

This material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We make abstract and chapter one visible for everyone.

All Project Topics on this site have complete 5(five) Chapters . Each Project Material include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.

To "DOWNLOAD" the complete material on this particular topic above click "HERE"

Do you want our Bank Accounts? please click HERE

To view other related topics click HERE

To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE

Do you want us to research for your new topic? if yes, click "HERE"

Do you have any question concerning our post/services? click HERE for answers to your questions

---

For more information contact us through Any of the following means:

Mobile No :+2348146561114 or +2347015391124

Email address :engr4project@gmail.com

Watsapp No :+2348146561114

---

IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.