A RESEARCH PROJECT
BY
NNAEMEKA ORIOHA
EE/2017/167
SUBMITTED TO
DEPARTMENT OF ELECTRICAL ELECTRONIC ENGINEERING FACULTY OF ENGINEERING CARITAS UNIVERSITY, AMORJI-NIKE, ENUGU.
IN PARTIAL FULFILLMENT OF THE REQUIREMENT FOR THE AWARD OF BACHELOR OF ENGINEERING (B.ENG)
AUGUST 2017
APPROVAL PAGE
This project has been read and approved by the undersigned as with the requirement at the department of Electrical Electronic Engineering of Caritas University Amorji Nike Enugu for the award of Bachelor of Engineering (B.Eng.) in Electrical Electronic Engineering.
---------------------------- -----------------------
Engr. Ejimorfor Date
(Project supervisor)
--------------------------- -----------------------
Engr. Ejimofor Date
(Head of Department)
------------------------------ ----------------------
External Supervisor
DECLARATION
I declare that this project material is an original work done by me under the supervision of Engr. Ejimorfor, department of electrical electronic engineering faculty of engineering caritas university, amorji-nike, enugu
DEDICATION
This project is dedicated to Almighty God and to my parents Engr. & Mrs. Chukwu A. Orioha and to my beloved brothers and sisters whose ever loving kindness and support has seen me through my years of studies.
ACKNOWLEDGEMENT
I wish to express my immense gratitude to God Almighty for his mercy, guidance and protection towards me for seeing me through the rigors of this work. I am greatly indebted to my supervisor Engr. Ejimofor for his kind gesture and whose critics lead to the achievement of this work. I also will remain grateful to the tremendous contribution of my lecturers Engr. Ojobor (the Dean of Engineering Faculty), Engr. Ejimofor (Head of Electrical Electronic Engineering Department), Engr. Mbah, Engr. Ochi, and all the staff of Electrical Electronic Engineering both academic and non academic staff for their intellectual upbringing. My special appreciation goes to my loving parents Engr. & Mrs. Chukwu A. Orioha, my grandparent, my uncles and aunties, my brothers and sisters whose moral and financial support cannot be over emphasized. Also my sincere gratitude and special regards to my friends too many to mention whose encouragement also lead to the success of this work.
This project work is on the construction of automatic night lightening system. Which aimed at activating a switch or AC lamp at sunset and deactivate it at sunrise.This automatic night lightening system can trigger a relay to operate an AC lamp at Sunset. The lamp remains on till morning and then turns off. This eliminates the need of switching the lamp or Backyard lamp daily and also helps to light the premises of the house when the occupants are out of station.
The circuit utilizes the light sensing property of LDR to activate the circuit. The LDR (Light Dependent Resistor) has very high resistance as high as 10 Meg ohms in dark which reduces to a few Ohms in bright light.
TABLE OF CONTENTS
TITLE PAGE
APPROVAL PAGE
DEDICATION
ACKNOWELDGEMENT
ABSTRCT
TABLE OF CONTENT
CHAPTER ONE
- INTRODUCTION
- AIM/OBJECTIVE OF THE PROJECT
- SCOPE OF THE PROJECT
- SCOPE OF THE PROJECT
- SIGNIFICANCE OF THE PROJECT
- LIMITATION OF THE PROJECT
- APPLICATION OF THE PROJECT
- PROJECT ORGANISATION
CHAPTER TWO
LITERATURE REVIEW
2.0 LITERATURE REVIEW
2.1 REVIEW OF LIGHT SENSOR
2.2 LDR STRUCTURE AND WORKING
2.3 REVIEW OF THE MAJOR COMPONENTS USED
CHAPTER THREE
3.0 CONSTRUCTION METHODOLOGY3.1 BLOCK DIAGRAM OF THE SYSTEM
3.2 CIRCUIT DIAGRAM
3.3 CIRCUIT DESCRIPTION
3.4 SYSTEM OPERATION
3.5 COMPONENTS LIST
3.6 DESCRIPTION OF MAJOR COMPONENTS USED
CHAPTER FOUR
4.0 RESULT ANALYSIS
4.1 CONSTRUCTION PROCEDURE AND TESTING
4.2 ASSEMBLING OF SECTIONS
4.3 CONSRUCTION OF THE CASING
4.4 TESTING OF SYSTEM OPERATION
4.5 INSTALLATION OF THE COMPLETED DESIGN
4.6 COST ANALYSIS
CHAPTER FIVE
- CONCLUSIONS
- RECOMMENDATION
5.3 REFERENCES
CHAPTER ONE
1.0 INTRODUCTION
The controlling of street lights or home lamps (or security lights) is usually maintained by an electrical department’s technician or home occupants on several occasions. This is not only precarious but also sometimes results in wastage of power because of the negligence or unusual circumstances on part of the technician in operating the lights on and off. Not only in case of street lights, even for controlling the home appliances like garden or outdoor lights, we can utilize the automatic night lightening system for automatic switching of the lights based on daylight’s intensity by using a light sensor.
Automatic night lightening system is a electrical project circuit by which we can switch on and off the electrical load appliances like lights, fans, coolers, air conditioners, street lights, etc., automatically based on the day-light intensity instead of manually operating the switches.
By using this method, manpower can be reduced to a great extent. In case of the street lights/lamp erected on highways it is not an easy task to manually control them, but, if uncontrolled, the chances of power wastage would increase. To get rid of this situation, the implementation of automatic light switch by using a dark/light sensor that switches lights automatically on and off is the best option.
1.1 OBJECTIVE OF THE PROJECT
The objective of this work is to design a device that will trigger lamps when darkness falls on the sensor (LDR). At the end of this work the student involved will be able to:
- understand how light dependent resistor works
- connect light dependent resistor unto a circuit
- know operation of an op-amp and the functions of the pins
1.2 SCOPE OF THE PROJECT
An automatic night lightening system is an electronic circuit consisting of LDR, transistor and Relay as connected in the main circuit, as shown below.
The circuit shown below requires a DC voltage, which can be supplied from a battery or by using a bridge rectifier instead of the battery. The bridge rectifier uses a step-down transformer to step-down the 230v into 12v.
This circuit is to switch ON the light when the LDR is illuminated. The light dependent resistor will have high resistance in darkness and low resistance in the light. The comparator used here has LDR connected to its inverting terminal and potentiometer connected to its non-inverting pin.
When the darkness falls on the Light Dependent Resistor, the comparator compares the voltages at the reference pin that is with the non-inverting pin and the inverting pin of the op-amp. If the voltage at the non-inverting pin is greater than the voltage at the inverting pin the transistor cannot be switched. If the voltage at non-inverting pin is less than the voltage at the inverting pin, the output of the comparator can switch the transistor.
Thus the relay switches and light/ or alarm are switched on when LDR is illuminated as transistor switches.
1.3 SIGNIFICANCE OF THE PROJECT
This device is very useful in that it distinguishes daylight and dark hours. This device eliminates the need of switching the Porch lamp or Backyard lamp daily and also helps to switch ON or OFF the premises of the house when the occupants are out of station.
1.4 LIMITATION OF THE PROJECT
One of the problems of this device is that any opaque material can trigger the device, such as human shadow, movement of animals or ants across the sensor can trigger the system
1.5 APPLICATIONS OF THE PROJECT
- Useful for automatic outdoor lighting or garden lighting at home.
- Useful for automatic switching of street lights.
- Useful for switching the hoardings on and off automatically.
- Useful for self-switching operation of displaying title hoardings of companies.
- Useful as a light detector circuit when the pin of the ic is reconfigured.
- Useful as a dark activated switch.
1.6 PROJECT WORK ORGANISATION
The various stages involved in the development of this project have been properly put into five chapters to enhance comprehensive and concise reading. In this project thesis, the project is organized sequentially as follows:
Chapter one of this work is on the introduction to automatic night lightening system. In this chapter, the background, significance, objective limitation and problem of dark activated alarm were discussed.
Chapter two is on literature review of automatic night lightening system. In this chapter, all the literature pertaining to this work was reviewed.
Chapter three is on design methodology. In this chapter all the method involved during the design and construction were discussed.
Chapter four is on testing analysis. All testing that result accurate functionality was analyzed.
Chapter five is on conclusion, recommendation and references.
This material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We make abstract and chapter one visible for everyone.
All Project Topics on this site have complete 5(five) Chapters . Each Project Material include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research for your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
You can also visit our facebook Page at fb.me/hyclas to view more our related construction (or design) pics
For more information contact us through Any of the following means:
Mobile No :+2348146561114 or +2347015391124 [Mr. Innocent]
Email address :engr4project@gmail.com
Watsapp No :+2348146561114
To View Our Design Pix: You can also visit our facebook Page at fb.me/hyclas for our design photos/pics.
IF YOU ARE SATISFIED WITH OUR SERVICES, PLEASE DO NOT FORGET TO INVITE YOUR FRIENDS AND COURSEMATES TO OUR PAGE.