DESIGN AND IMPLEMENTATION OF LIGHTING SWITCHING CONTROL SYSTEM (INTERFACE)
USER'S INSTRUCTIONS: The project work you are about to view is on "design and implementation of lighting switching control system (interface)". Please, sit back and study the below research material carefully. This project topic "design and implementation of lighting switching control system (interface)" have complete 5(five) Chapters. The complete Project Material/writeup include: Abstract + Introduction + etc + Literature Review + methodology + etc + Conclusion + Recommendation + References/Bibliography.Our aim of providing this "design and implementation of lighting switching control system (interface)" project research material is to reduce the stress of moving from one school library to another all in the name of searching for "design and implementation of lighting switching control system (interface)" research materials. We are not encouraging any form of plagiarism. This service is legal because, all institutions permit their students to read previous projects, books, articles or papers while developing their own works.
TITLE PAGE
DESIGN AND IMPLEMENTATION OF LIGHTING SWITCHING CONTROL SYSTEM (INTERFACE)
BY
---
EE/H2013/01430
DEPARTMENT OF ----
SCHOOL OF ---
INSTITUTE OF ---
DECEMBER,2018
APPROVAL PAGE
This is to certify that the research work, "design and implementation of lighting switching control system (interface)" by ---, Reg. No. EE/H2007/01430 submitted in partial fulfillment of the requirement award of a Higher National Diploma on --- has been approved.
By
--- . ---
Supervisor Head of Department.
Signature………………. Signature……………….
……………………………….
---
External Invigilator
DEDICATION
This project is dedicated to Almighty God for his protection, kindness, strength over my life throughout the period and also to my --- for his financial support and moral care towards me.Also to my mentor --- for her academic advice she often gives to me. May Almighty God shield them from the peril of this world and bless their entire endeavour Amen.
ACKNOWLEDGEMENT
The successful completion of this project work could not have been a reality without the encouragement of my --- and other people. My immensely appreciation goes to my humble and able supervisor mr. --- for his kindness in supervising this project.
My warmest gratitude goes to my parents for their moral, spiritual and financial support throughout my study in this institution.
My appreciation goes to some of my lecturers among whom are Mr. ---, and Dr. ---. I also recognize the support of some of the staff of --- among whom are: The General Manager, Deputy General manager, the internal Auditor Mr. --- and the ---. Finally, my appreciation goes to my elder sister ---, my lovely friends mercy ---, ---, --- and many others who were quite helpful.
PROJECT DESCRIPTION: This work "design and implementation of lighting switching control system (interface)" research material is a complete and well researched project material strictly for academic purposes, which has been approved by different Lecturers from different higher institutions. We made Preliminary pages, Abstract and Chapter one of "design and implementation of lighting switching control system (interface)" visible for everyone, then the complete material on "design and implementation of lighting switching control system (interface)" is to be ordered for. Happy viewing!!!
TABLE OF CONTENT
COVER PAGE
APPROVAL PAGE
DEDICATION
ACKNOWLEDGEMENT
TABLE OF CONTENT
1.1 BACKGROUND OF THE STUDY
1.2 PROBLEM STATEMENT
1.3 OBJECTIVES OF STUDY
1.4 SIGNIFICANCE OF STUDY
1.5 SCOPE OF STUDY
1.6 LIMITATION OF STUDY
1.7 DEFINITION OF TERMS\
CHAPTER TWO
2.1INTRODUCTION
- CATEGORIES OF SWITCHES
2.3COMPUTERS AS A SWITCH
2.4 SERIAL PORTS
2.4.1 TYPICAL LOCATIONS FOR SERIAL PORTS
- I/0 INTERFACES FROM SERIAL AND PARALLEL TO IEEE 1394 AND USB
CHAPTER THREE
METHODOLOGY
- INTRODUCTION
- ANALYSIS OF THE EXISTING SYSTEM
- ADVANTAGES OF THE EXISTING SYSTEM
3.3.2 DISADVANTAGES OF THE EXISTING SYSTEM
3.3 JUSTIFICATION OF THE PROPOSED SYSTEM
3.3.1 ADVANTAGES OF THE PROPOSED SYSTEM
3.3.2 DISADVANTAGES OF THE PROPOSED SYSTEM
3.4 CONNECTING THE PORT TO EXTERNAL DEVICE INTERFACE
3.5 SWITCHING STAGE
3.5.1 RELAY STAGE
3.5.1.1 RELAYS
3.5.1.2 CHOOSING A RELAY
- ADVANTAGES OF RELAYS
3.6 RESEARCH METHODOLOGY
3.7 THE DIAGRAM BELOW SHOWS THE PIN-OUT OF THE 8051 MICRO
CONTROLLERS
- POWER SUPPLY
- TRANSFORMER
CHAPTER FOUR
4.1 INTRODUCTION
4.2 OVER VIEW OF DESIGN
4.3 MAIN MENU
4.4 MAIN MENU
4.3 CHOICE AND JUSTIFICATION OF PROGRAMMING LANGUAGE
4.4. SYSTEM REQUIREMENT
4.5 IMPLEMENTATION PLANS
4.6MAINTENANCE DETAILS
CHAPTER FIVE
5.0 SUMMARY
5.1 CONCLUSION
5.3 RECOMMENDATION
5.4 SUGGESTION FOR FURTHER STUDIES
CHAPTER ONE
INTRODUCTION
1.1 BACKGROUND OF THE STUDY
Traditionally, high control in home and office environments takes place through switches (on/off), deals and sliders (dimmers) and sometimes motion sensors. These controls can be incorporated in the built environment such as walls, or attached to lights that people place themselves (desk lamps, bed side lights). This often leads to a jumble of controls each with their own location, interaction style, and focus.
This project is a demonstration of how a PC can be used as a control signal generation subsystem capable of generating programmable control signals for power equipment. Early studies reveal that using PC for power management was often fou7nd to be up to 25% more than energy star compliant methods. However, recent assessments have found higher rates, and was estimated that for power management.
Switching control is a good replacement for conventional pneumatic or Electro chemical high voltage AC control. This equipment is capable of not only control but energy management and system diagnostic functions. The PC control in inherentlyhas more accurate control because it reduces maintenance and recalibration problems common with pneumatic and mechanical systems.
It offers other unique advantages like subsystem coordination, optimum start, diversity analysis and retrofit identification.
This design begins with the fact that a computer is needed to light bulbs of high AC rating. This immediately suggests that an interface of the PC is needed to handle the mismatch in voltage and currents between the PC and bulbs.
Secondly the control data from the PC program are logic levels in serial format and at high frequency. This again means that the interface should understand the protocol of communication and convert it to the necessary parallel control singed. Due to lack of resources, the project will not be real but simulated. This system will represent for more than just manual on/off control. The system comprises of two major components, output device, and input device. Output devices work behind the scenes to control the lights by switching them off or on. Input device are the switcher i.e. the button or sensors.
1.2 PROBLEM STATEMENT
- No prior information whether a bulb is dead or not
- There is always a problem of one or two poles using one switch. That is each pole with a switch which could amount to lots of expenses. Each pole with their own switch and location.
- It consumes ones time in the sense that one will more from one pole to another. Just to put one or off the light.
1.3 OBJECTIVES OF STUDY
This professional documentation focuses on using a serial interface hardware built on microcontroller and max 232 serial converters. The ensure that the high negative -15 volts and + 15 volts of the serial RS232 comport is converted and programmed to suit the CPC logic levels. The system is responsible for controlling,
energy management and system diagnostic functions. Tracking of all lighting activities, especially bulbs. In a place where prepaid meter is in use, it could help reduce the cost.
1.4 SIGNIFICANCE OF STUDY
This system is important considering the fat that only a push of a button can switch off or on the light connected within the system. With this system, one can easily be on his/her bed and switch off or on the lights. |
The system is safe therefore children can also switch off or on the light when their parents or guardians are not close. The system is very necessary in the sense that it gives you what you want at any needed time. The system also keepstrack of all activities (bulb).
1.5 SCOPE OF STUDY
The research will focus on creating a computerized system that will switch on or off light on the street and equally control the power aspect.
The research will also focus on light bit microcontroller issues discreet digital electronics in appliance control. Intel controllers that can complete application are typically relegated to switches and times are also discussed. It will be a system that maximizes user efficiency and user convenience.
1.6 LIMITATION OF STUDY
One of the major setbacks of this work is finance. Due to lack of finance, one could not bring the system to life. Inadequate electricity also contributed to the setback of this work.
1.7 DEFINITION OF TERMS
Pneumatic: the branch of physics with the mechanical properties of air and other gases.
Retrofit Identification: To modify something such as a machine or a building by adding newly developed parts or devices that were not available where the machine or building was made.
Diversy analysis: A variety of something such as opinion, colour, or style
CHAPTER TWO: The chapter one of this work has been displayed above. The complete chapter two of "design and implementation of lighting switching control system (interface)" is also available. Order full work to download. Chapter two of "design and implementation of lighting switching control system (interface)" consists of the literature review. In this chapter all the related work on "design and implementation of lighting switching control system (interface)" was reviewed.
CHAPTER THREE: The complete chapter three of "design and implementation of lighting switching control system (interface)" is available. Order full work to download. Chapter three of "design and implementation of lighting switching control system (interface)" consists of the methodology. In this chapter all the method used in carrying out this work was discussed.
CHAPTER FOUR: The complete chapter four of "design and implementation of lighting switching control system (interface)" is available. Order full work to download. Chapter four of "design and implementation of lighting switching control system (interface)" consists of all the test conducted during the work and the result gotten after the whole work
CHAPTER FIVE: The complete chapter five of design and construction of a "design and implementation of lighting switching control system (interface)" is available. Order full work to download. Chapter five of "design and implementation of lighting switching control system (interface)" consist of conclusion, recommendation and references.
To "DOWNLOAD" the complete material on this particular topic above click "HERE"
Do you want our Bank Accounts? please click HERE
To view other related topics click HERE
To "SUMMIT" new topic(s), develop a new topic OR you did not see your topic on our site but want to confirm the availiability of your topic click HERE
Do you want us to research your new topic? if yes, click "HERE"
Do you have any question concerning our post/services? click HERE for answers to your questions
For more information contact us through any of the following means:
Mobile No 
:+2348146561114 or +2347015391124 [Mr. Innocent]
Email address 
:engr4project@gmail.com
Watsapp No 
:+2348146561114
COUNTRIES THAT FOUND OUR SERVICES USEFUL
Australia, Botswana, Canada, Europe, Ghana, Ireland, India, Kenya, Liberia, Malaysia, Namibia, New Zealand, Nigeria, Pakistan, Philippines, Singapore, Sierra Leone, South Africa, Uganda, United States, United Kindom, Zambia, Zimbabwe, etc
Support: +234 8146561114 or +2347015391124
Watsapp No :+2348146561114
Email Address :engr4project@gmail.com
FOLLOW / VISIT US VIA:
